Contact Us Live Chat or 1-888-220-8330
Search Bar
Search by Part Number or Keywords
  • My Garage
  • My Account
  • Cart
  • Body & Mirrors
  • Chassis & Brakes
  • Engine & Drivetrain
  • Electrical & Lighting
Help Center
< Back ×
  • Body & Mirrors
  • Chassis & Brakes
  • Engine & Drivetrain
  • Electrical & Lighting
Login/Register My Account Track Order Help Center Contact Us
Replacement and OEM Parts for 2007 Chevrolet Equinox Third Brake Light

2007 Chevrolet Equinox Third Brake Light

My Vehicle Change Vehicle
2007 Chevrolet Equinox
Change Vehicle
Vehicle Options
We need more information about your vehicle to make a correct determination of fitment
< Back to View All
Tail Lights
  • Department
  • Prices

1 Product found

5 Q&A for Third Brake Light Repair
Show Item:
  • 30
  • 60
  • 90
Sort by:
Recommended
Filter
Sort
View by
  • OEM 2007 Chevrolet Equinox High Mount Lamp Diagram - 25792000
    View Related Parts

    OEM (Genuine) 2007 Chevrolet Equinox High Mount Lamp

    PartNumber: 25792000
    OEM 2007 Chevrolet Equinox High Mount Lamp - 25792000
    Product Specifications
    • Other Names: High Mount Lamp
    • Item Dimensions: 5.1 x 5.1 x 20.1 inches
    • Item Weight: 0.70 Pounds
    • Fitment Type: Direct Replacement
    • Replaces: 10363039
    • Part Description: 2007 Chevrolet Equinox High Mount Lamp
    More Info
    Vehicle Fitment
    • 2007 Chevrolet Equinox | LS, LT, LTZ, Sport | 6 Cyl 3.4 L GAS, 6 Cyl 3.6 L GAS

FAQ for Third Brake Light Repair

Q: What's the terminal repair procedure?
A:
You should use the appropriate terminal and follow the instructions in the J-38125 to replace the terminal.
By Bob
GM Specialist
01/11/2022
Q: What does the J-38125 SIR/SRS Terminal Repair Kit contain?
A:
It contains the following components: various terminated leads for sensing and diagnostic module (SDM) terminal replacement, various connector positive assurance (CPA) locks for SIR/SRS connectors, the base of steering column pigtail connectors part number 12085514 and yellow vinyl electrical tape.
By Bob
GM Specialist
01/11/2022
Q: What should I know about terminal position assurance (TPA)?
A:
The TPA on this connector cannot be removed unless the terminals are removed first. The TPA will come out of the connector body, but only slightly. When the TPA is slightly raised the terminals can be removed. Using excessive force to remove the TPA with the terminals still in the connector will damage the connector.
By Bob
GM Specialist
01/11/2022
Q: What's the recommended torque for the center high-mounted stop lamp screws?
A:
The recommended torque is 2.5 N.m (22 lb in).
By Bob
GM Specialist
01/11/2022
Q: How many center high-mounted stop lamp screws are needed?
A:
2center high mounted stop lamp screws attach.
By Bob
GM Specialist
01/11/2022

FAQ for Other Repair Info

Q: How to remove the Starter Motor?
A:
You will need to disconnect the battery negative cable, then raise and suitably support the vehicle. Then you should remove the Starter motor solenoid positive terminal nut and electrical wires, the starter motor solenoid S terminal nut and electrical wire, the torque converter cover bolt, the torque converter cover, the starter motor bolts, and the starter motor.
Q: How to install the underhood electrical center or junction block?
A:
You may need to install each of the following 68-way connectors into its proper location including fuse block case, forward lamp 68-way connector, engine 68-way connector, and I/P 68-way connector. Then you can push down on each connector until it is fully secured into the fuse block, connect the I/P connectors, tighten the bolts on the top of the fuse block, and tighten the underhood accessory wiring junction block harness retaining bolts to 4 N.m (35 lb in), next reconnect the positive battery cable and EPS at the end of the fuse block with the nut and tighten it to 17 N.m (13 lb-ft), finally install the Fuse Box cover and connect the negative battery cable.
Q: What's the tip for replacing the power mirror switch?
A:
You may squeeze the tabs inward from the rear of the outlet assembly and push the power Mirror Switch out through the front of the outlet.