< Back ×
My Vehicle Change Vehicle
2007 Chevrolet Equinox
< Back to View All
Cigarette Lighters
- Department
- Prices
OEM (Genuine) 2007 Chevrolet Equinox Lighter Housing
PartNumber: 25774623
Product Specifications- Item Dimensions: 2.8 x 1.5 x 1.1 inches
- Item Weight: 0.30 Pounds
- Fitment Type: Direct Replacement
- Replaces: 1999477, 12450044, 01999477
- Part Description: 2007 Chevrolet Equinox Lighter Housing
Vehicle Fitment- 2007 Chevrolet Equinox | L, LS, LT, LTZ, Premier, RS, Sport | 4 Cyl 1.5 L GAS, 4 Cyl 1.6 L DIESEL, 4 Cyl 2.0 L GAS, 6 Cyl 3.4 L GAS, 6 Cyl 3.6 L GAS
$7.04 MSRP:$10.60You Save: $3.56 (34%)
OEM (Genuine) 2007 Chevrolet Equinox Receptacle Asm, Cigarette Lighter
PartNumber: 25776667
Product Specifications- Item Dimensions: 2.8 x 1.6 x 1.2 inches
- Item Weight: 0.30 Pounds
- Fitment Type: Direct Replacement
- Replaces: 12450043
- Part Description: 2007 Chevrolet Equinox Receptacle Asm, Cigarette Lighter
Vehicle Fitment- 2007 Chevrolet Equinox | LS, LT, LTZ, Sport | 6 Cyl 3.4 L GAS, 6 Cyl 3.6 L GAS
$12.58 MSRP:$18.70You Save: $6.12 (33%)
FAQ for Cigarette Lighters Repair
Q: How to install the cigar lighter receptacle or 12-volt accessory power receptacle?
A:
You may need to route the connector through the retainer, align the accessory power receptacle retainer to the slot in the opening, install the retainer by pressing into place fully seated, connect the electrical connector to the receptacle, align the tabs on the receptacle to the slots in the retainer, then install the accessory power receptacle and seat it fully, next install the accessory power receptacle fuse.
By Bob
GM Specialist
29/10/2022Q: How do you test for short to ground with a DMM?
A:
You can remove the power feed (i.e. fuse, control module) from the suspect circuit, disconnect the load, then set the rotary dial of the DMM to the ohm position, connect one lead of the DMM to one end of the circuit to test, connect the other lead of the DMM to a good ground. If the DMM does NOT display infinite resistance (OL), there is a short to ground in the circuit.
By Bob
GM Specialist
29/10/2022Q: How to remove the receptacle?
A:
First, you can look into the receptacle. There are two 3 mm (0.11 in) tab windows 12 mm (0.47 in) from the front of the receptacle. The J 42059 pushes the plastic latches from these tab windows and the receptacle can be pulled straight out. Second, you can place one side of the °T° portion of the J 42059 into the tab window. The J 42059 will not fit straight into the receptacle. You can angle the J 42059 slightly for insertion into the receptacle. Then you insert the other side of the °T° into the opposite tab window. You must move the J 42059 handle horizontally to engage the other tab window. Finally, you can use the J 42059 to pull the receptacle straight out.
By Bob
GM Specialist
29/10/2022Q: What's the preliminary procedure for removing the cigar lighter receptacle or 12-volt accessory power receptacle?
A:
The procedure is to remove the auxiliary power outlet fuse from the fuse block.
By Bob
GM Specialist
29/10/2022Q: What tools are needed to replace the cigar lighter receptacle or 12-volt accessory power receptacle?
A:
You will need J 42059 Cigar Lighter Socket Remover.
By Bob
GM Specialist
29/10/2022Q: What should be done if J 42059 tool fails to release the lighter socket from the retainer?
A:
You will need to insert a small grinding tool with a cutoff wheel into the socket, remove the plastic latches in the 3 mm (0.11 in) square windows, then use the J 42059 as directed above to remove the socket.
By Bob
GM Specialist
29/10/2022See more FAQs (1)