< Back ×
My Vehicle Change Vehicle
2007 Chevrolet Colorado
< Back to View All
Steering Racks & Gearboxes
- Department
- Prices
OEM (Genuine) 2007 Chevrolet Colorado Gear Assembly
PartNumber: 15951338
Product Specifications- Notes: W/O 4WD, Z85; Canyon, Colorado; 2WD; Chassis Pkg.
- Other Names: Gear Assembly, Steering Gear
- Item Dimensions: 29.6 x 7.4 x 6.9 inches
- Item Weight: 7.60 Pounds
- Fitment Type: Direct Replacement
- Replaces: 25817575, 15864178, 15921544
- Part Description: 2007 Chevrolet Colorado Gear Assembly
Vehicle Fitment- 2007 Chevrolet Colorado | LS, LT, WT | 4 Cyl 2.8 L GAS, 4 Cyl 2.9 L GAS, 5 Cyl 3.5 L GAS, 5 Cyl 3.7 L GAS, 8 Cyl 5.3 L GAS
$451.30 MSRP:$746.95You Save: $295.65 (40%)OEM (Genuine) 2007 Chevrolet Colorado Gear Assembly
PartNumber: 25817574
Product Specifications- Notes: W/4WD;W/O 4WD, Z71; Canyon, Colorado; 2WD; Off Road Pkg.;Canyon, Colorado; 4WD
- Other Names: Gear Assembly, Steering Gear
- Item Dimensions: 64.6 x 11.2 x 11.2 inches
- Item Weight: 30.50 Pounds
- Fitment Type: Direct Replacement
- Replaces: 15921545
- Part Description: 2007 Chevrolet Colorado Gear Assembly
Vehicle Fitment- 2007 Chevrolet Colorado | LS, LT, WT | 4 Cyl 2.8 L GAS, 4 Cyl 2.9 L GAS, 5 Cyl 3.5 L GAS, 5 Cyl 3.7 L GAS
$493.76 MSRP:$931.64You Save: $437.88 (48%)OEM (Genuine) 2007 Chevrolet Colorado Gear Asm-Steering (W/ Steering Linkage Tie Rod)
PartNumber: 15864177Product Specifications- Notes: W/O 4WD, Zq8; Canyon, Colorado; 2WD; Sport Chassis Pkg.
- Other Names: Gear Assembly, Steering Gear
- Item Dimensions: 66.4 x 9.9 x 5.8 inches
- Item Weight: 20.60 Pounds
- Fitment Type: Direct Replacement
- Replaces: 25817576, 25912267, 15921543, 15270454
- Part Description: 2007 Chevrolet Colorado Gear Asm-Steering (W/ Steering Linkage Tie Rod)
Vehicle Fitment- 2007 Chevrolet Colorado | LS, LT, WT | 4 Cyl 2.8 L GAS, 4 Cyl 2.9 L GAS, 5 Cyl 3.5 L GAS, 5 Cyl 3.7 L GAS
FAQ for Steering Gearbox Repair
Q: What is the recommended torque for the inner tie rod?
A:
The recommended torque is 100 N.m (74 lb-ft).
By Bob
GM Specialist
01/11/2022Q: How to adjust the Rack and Pinion Gear Rack Bearing Preload-Off Vehicle?
A:
You need to loosen the adjuster plug lock nut, then tighten the adjuster plug, and tighten the adjuster plug lock nut to the steering gear housing.
By Bob
GM Specialist
01/11/2022Q: How to remove the Power Steering Gear?
A:
You need to remove both of the front tire and wheel assemblies, remove the engine protection shield if equipped, then disconnect the outer tie rod end from the steering knuckle, disconnect the power steering hose assembly from the steering gear, then remove the coupler clamp bolt from the intermediate shaft, and separate the intermediate shaft from the steering gear. Next, you should remove the steering gear vertical mounting nuts, the washers and the bolts, the steering gear horizontal mounting nuts, the washers, the bolts, and the crossmember, 2WD only, and finally remove the steering gear from the vehicle.
By Bob
GM Specialist
01/11/2022Q: What kind of special tools will be required in the adjustment of the Rack and Pinion Gear Rack Bearing Preload-Off Vehicle?
A:
The tools required include J 45059 Torque Angle Meter.
By Bob
GM Specialist
01/11/2022Q: What is the recommended torque for the isolator clamp bolts?
A:
The recommended torque is 100 N.m (74 lb-ft).
By Bob
GM Specialist
01/11/2022Q: What is the recommended torque for the adjuster plug lock nut?
A:
The recommended torque is 60 N.m (44 lb-ft).
By Bob
GM Specialist
01/11/2022Q: What kind of special tools will be required when serving the Rack and Pinion Inner Tie Rod-Off Vehicle (Magnasteer)?
A:
The tools required include J 34028 Inner Tie Rod Wrench.
By Bob
GM Specialist
01/11/2022Q: How to remove the Steering Gear Cylinder Pipe Assemblies/O-Ring Seals-Off Vehicle?
A:
You need to loosen both cylinder line fittings on the cylinder end of the gear assembly, loosen both fittings on the cylinder line assemblies at the valve end of the gear assembly, then remove both cylinder line assemblies from the rack and pinion gear assembly, and remove and discard the O-ring seals from the valve end of the line.
By Bob
GM Specialist
01/11/2022Q: What should be noted about the pipe wrench in the removal?
A:
The pipe wrench must be placed at the valve end of the steering gear and positioned up against the inner tie rod housing. Placing the pipe wrench in any other location will cause damage to the steering gear.
By Bob
GM Specialist
01/11/2022Q: What is the recommended torque for the cylinder end fittings?
A:
The recommended torque is 27 N.m (20 lb-ft).
By Bob
GM Specialist
01/11/2022See more FAQs (5)