Contact Us Live Chat or 1-888-220-8330
Search Bar
Search by Part Number or Keywords
  • My Garage
  • My Account
  • Cart
  • Body & Mirrors
  • Chassis & Brakes
  • Engine & Drivetrain
  • Electrical & Lighting
Help Center
< Back ×
  • Body & Mirrors
  • Chassis & Brakes
  • Engine & Drivetrain
  • Electrical & Lighting
Login/Register My Account Track Order Help Center Contact Us
Replacement and OEM Parts for 2007 Chevrolet Colorado Brake Light Switches

2007 Chevrolet Colorado Brake Light Switches

My Vehicle Change Vehicle
2007 Chevrolet Colorado
Change Vehicle
Vehicle Options
We need more information about your vehicle to make a correct determination of fitment
< Back to View All
Light Relays, Switches & Control Modules
  • Department
  • Prices

1 Product found

3 Q&A for Brake Light Switches Repair
Show Item:
  • 30
  • 60
  • 90
Sort by:
Recommended
Filter
Sort
View by
  • OEM 2007 Chevrolet Colorado Stoplamp Switch Diagram - 20913529
    View Related Parts

    OEM (Genuine) 2007 Chevrolet Colorado Stoplamp Switch

    PartNumber: 20913529
    OEM 2007 Chevrolet Colorado Stoplamp Switch - 20913529
    Product Specifications
    • Notes: Canyon, Colorado
    • Other Names: Stoplamp Switch
    • Item Dimensions: 3.2 x 2.2 x 2.1 inches
    • Item Weight: 0.40 Pounds
    • Fitment Type: Direct Replacement
    • Replaces: 25796381, 15186470, 15912229
    • Part Description: 2007 Chevrolet Colorado Stoplamp Switch
    More Info
    Vehicle Fitment
    • 2007 Chevrolet Colorado | Base, LS, LT, Sport, Sport LS, WT, Z71, Z71 LS, Z85, Z85 LS | 4 Cyl 2.8 L GAS, 4 Cyl 2.9 L GAS, 5 Cyl 3.5 L GAS, 5 Cyl 3.7 L GAS, 8 Cyl 5.3 L GAS
    $14.12 MSRP: $23.35
    You Save: $9.23 (40%)

FAQ for Brake Light Switches Repair

Q: What is the proper way to install the stop lamp switch?
A:
You should install the switch retainer, position the switch near the bracket, and ensure the switch key-way is properly indexed to the plastic retainer, then install and adjust the switch, connect the stop lamp switch electrical connectors, and finally check the switch for proper operation.
By Bob
GM Specialist
29/10/2022
Q: How to adjust the stop lamp switch?
A:
You need to rotate the switch counterclockwise, allowing the retainer to release, then pull the brake pedal rearward to a full stop, and push the switch inward fully until the switch body contacts the brake pedal arm striker plate, then rotate the switch clockwise until a °click° is heard. The switch is properly adjusted when there is a 7 mm (0.028 in) clearance between the end of the switch barrel and the striker plate on the brake pedal arm.
By Bob
GM Specialist
29/10/2022
Q: How to remove the stop lamp switch?
A:
You need to disconnect the stop lamp switch electrical connectors, rotate the switch counterclockwise, remove the switch from the bracket, remove the switch, and remove the switch retainer.
By Bob
GM Specialist
29/10/2022

FAQ for Other Repair Info

Q: How to remove the Backup Lamp Switch?
A:
You need to raise and support the vehicle, disconnect the backup lamp switch electrical connector at the pigtail, then open the tie strap securing the pigtail to the transmission, and remove the backup lamp switch with the aluminum washer.
Q: How to remove the Body Control Module (BCM)?
A:
You need to ensure the ignition switch is in the OFF position first, then remove the right front hinge pillar trim panel, disconnect the body wiring harness electrical connector from the BCM, release the fastener retaining the body wiring harness electrical connector to the BCM, next remove the 2 fasteners retaining the BCM to the hinge pillar, remove the BCM from the hinge pillar by unlocking the integral tab, and remove the BCM from the vehicle.
Q: How to install the Hazard Warning Switch?
A:
You should position the switch to the trim plate, ensure the switch key-way is indexed to the trim plate, install the switch to the trim plate, connect the hazard switch electrical connector, and finally install the I/P accessory trim plate.