Contact Us Live Chat or 1-888-220-8330
Search Bar
Search by Part Number or Keywords
  • My Garage
  • My Account
  • Cart
  • Body & Mirrors
  • Chassis & Brakes
  • Engine & Drivetrain
  • Electrical & Lighting
Help Center
< Back ×
  • Body & Mirrors
  • Chassis & Brakes
  • Engine & Drivetrain
  • Electrical & Lighting
Login/Register My Account Track Order Help Center Contact Us
Replacement and OEM Parts for 2007 Cadillac Escalade ESV Crankshaft Position Sensor

2007 Cadillac Escalade ESV Crankshaft Position Sensor

My Vehicle Change Vehicle
2007 Cadillac Escalade ESV
Change Vehicle
Vehicle Options
We need more information about your vehicle to make a correct determination of fitment
< Back to View All
Engine Sensors, Switches & Relays
  • Department
  • Brands
  • Prices

3 Products found

4 Q&A for Crankshaft Position Sensor Repair
Show Item:
  • 30
  • 60
  • 90
Sort by:
Recommended
Filter
Sort
View by

FAQ for Crankshaft Position Sensor Repair

Q: How do you install the Crankshaft Position Sensor?
A:
You need to install the CKP sensor and the CKP sensor bolt, connect the engine wiring harness electrical connector to the CKP sensor, install the starter and perform the CKP system variation learn procedure.
By Bob
GM Specialist
29/10/2022
Q: What will the scan tool instruct you to do?
A:
It will instruct you to accelerate to wide open throttle (WOT), release the throttle when fuel cut-off occurs and observe fuel cut-off for the applicable engine. The engine should not accelerate beyond calibrated RPM value. Next, it instructs you to release the throttle immediately if the value is exceeded, block the drive wheels, set the parking brake, cycle ignition from OFF to ON, apply and hold the brake pedal, start, and idle the engine and turn A/C OFF. The vehicle must remain in Park or Neutral.
By Bob
GM Specialist
29/10/2022
Q: What does the scan tool monitor?
A:
It monitors CKP sensors activity, camshaft position (CMP) sensor activity, and engine coolant temperature (ECT). If the ECT is not warm enough, idle the engine until the engine coolant temperature reaches the correct temperature.
By Bob
GM Specialist
29/10/2022
Q: How do you remove the Crankshaft Position Sensor?
A:
You need to remove the starter, disconnect the engine wiring harness electrical connector from the crankshaft position (CKP) sensor, clean the area around the CKP sensor before removal to avoid debris from entering the engine, and remove the CKP sensor bolt and the CKP sensor.
By Bob
GM Specialist
29/10/2022

FAQ for Other Repair Info

Q: How do you install the engine oil pressure sensor and/or switch?
A:
You need to apply a sealant to the threads of the new Oil Pressure Sensor. If equipped with active fuel management perform the following step, using J 41712 or equivalent, and install the oil pressure sensor and washer. If not equipped with active fuel management, perform the following step, using J 41712 or equivalent. Install the oil pressure sensor and washer, connect the engine harness electrical connector to the oil pressure sensor and install the intake manifold.
Q: How do you remove the engine oil level sensor and/or switch?
A:
You need to place a suitable drain pan under the oil pan drain plug, remove the oil pan drain plug, allow the oil pan to drain completely, re-install the oil pan drain plug until snug, remove the drain pan from under the vehicle, disconnect the engine harness electrical connector from the oil level sensor and remove the oil level sensor from the oil pan.
Q: What is the proper way to install the accelerator pedal position sensor?
A:
The proper way is to position the accelerator pedal to the accelerator pedal bracket and connect the APP sensor electrical connector and a scan tool to the diagnostic port to test for proper throttle-opening and throttle-closing range. Then operate the accelerator pedal and monitor the throttle angles. The accelerator pedal should operate freely, without binding, between a closed throttle, and a wide open throttle (WOT) and install the knee bolster.