< Back ×
My Vehicle Change Vehicle
2007 Buick Terraza
< Back to View All
Power Steering Lines & Hoses
- Department
- Brands
- Prices
OEM (Genuine) 2007 Buick Terraza Cooling Pipe
PartNumber: 15777213
Product Specifications- Notes: W/O AWD; With Cooler From Gear; Terraza, Uplander; W/O AWD
- Item Dimensions: 28.2 x 26.0 x 10.1 inches
- Item Weight: 1.60 Pounds
- Fitment Type: Direct Replacement
- Part Description: 2007 Buick Terraza Cooling Pipe
Vehicle Fitment- 2007 Buick Terraza | CX, CXL | 6 Cyl 3.5 L GAS, 6 Cyl 3.9 L FLEX, 6 Cyl 3.9 L GAS
$95.56 MSRP:$152.41You Save: $56.85 (38%)
Gates® Power Steering Return Line Hose Assembly From Gear for 2007 Buick Terraza
PartNumber: 365859Product Specifications- Notes: w/Cooler
- End 1 Diameter: 16 mm
- End 1 Type: Male O-Ring
- End 2 Diameter: 0.375"
- End 2 Type: Beaded Tube
- Length: 116.75"
- UPC: 770075547686
- Part Description: 2007 Buick Terraza Power Steering Return Line Hose Assembly From Gear
Vehicle Fitment- 2007 Buick Terraza | All Trims | 6 Cyl 3.9L
$57.75
OEM (Genuine) 2007 Buick Terraza Pipe Kit, Steering Gear Light
PartNumber: 88963469
Product Specifications- Notes: W/O AWD
- Location: Driver Side
- Other Names: Pipe Kit
- Item Dimensions: 10.9 x 5.0 x 2.1 inches
- Item Weight: 0.70 Pounds
- Fitment Type: Direct Replacement
- Part Description: 2007 Buick Terraza Pipe Kit, Steering Gear Light
Vehicle Fitment- 2007 Buick Terraza | CX, CXL | 6 Cyl 3.5 L GAS, 6 Cyl 3.9 L FLEX, 6 Cyl 3.9 L GAS
$15.15 MSRP:$30.53You Save: $15.38 (51%)
Gates® Power Steering Pressure Line Hose Assembly for 2007 Buick Terraza
PartNumber: 365604Product Specifications- End 1 Diameter: 16 mm
- End 1 Type: Male O-Ring
- End 2 Diameter: 18 mm
- End 2 Diameter (mm): 18 mm
- End 2 Type: Male O-Ring
- Length: 67.75"
- Switch Port: Without Switch Port
- UPC: 770075506898
- Part Description: 2007 Buick Terraza Power Steering Pressure Line Hose Assembly
Vehicle Fitment- 2007 Buick Terraza | All Trims | 6 Cyl 3.9L
Gates® Power Steering Return Line Hose Assembly Cooler To Reservoir for 2007 Buick Terraza
PartNumber: 365576Product Specifications- End 1 Diameter: 0.375"
- End 1 Type: I.D. Hose
- End 2 Type: I.D. Hose
- Length: 44"
- UPC: 770075396383
- Part Description: 2007 Buick Terraza Power Steering Return Line Hose Assembly Cooler To Reservoir
Vehicle Fitment- 2007 Buick Terraza | All Trims | 6 Cyl 3.9L
OEM (Genuine) 2007 Buick Terraza Hose Asm, P/S Gear Inlet
PartNumber: 19333426
Product Specifications- Notes: 3.9 Liter; Terraza, Uplander; W/O AWD; 3.9l
- Other Names: Power Steering Pressure Hose, Pressure Hose
- Item Dimensions: 28.1 x 17.5 x 9.4 inches
- Item Weight: 1.90 Pounds
- Fitment Type: Direct Replacement
- Replaces: 15777210
- Part Description: 2007 Buick Terraza Hose Asm, P/S Gear Inlet
Vehicle Fitment- 2007 Buick Terraza | CX, CXL | 6 Cyl 3.9 L FLEX, 6 Cyl 3.9 L GAS
OEM (Genuine) 2007 Buick Terraza Pipe Asm-P/S Pump Inlet
PartNumber: 15893685
Product Specifications- Notes: 3.9 Liter; From Cooler To Reservoir; Terraza, Uplander; 3.9l
- Other Names: Inlet Pipe, Power Steering Return Hose
- Item Dimensions: 24.0 x 10.9 x 10.5 inches
- Item Weight: 1.90 Pounds
- Fitment Type: Direct Replacement
- Part Description: 2007 Buick Terraza Pipe Asm-P/S Pump Inlet
Vehicle Fitment- 2007 Buick Terraza | CX, CXL | 6 Cyl 3.9 L FLEX, 6 Cyl 3.9 L GAS
OEM (Genuine) 2007 Buick Terraza Pipe Kit, Steering Gear Right
PartNumber: 88963470
Product Specifications- Notes: W/O AWD
- Location: Passenger Side
- Other Names: Pipe Kit
- Item Dimensions: 18.7 x 4.7 x 2.4 inches
- Item Weight: 0.70 Pounds
- Fitment Type: Direct Replacement
- Part Description: 2007 Buick Terraza Pipe Kit, Steering Gear Right
Vehicle Fitment- 2007 Buick Terraza | CX, CXL | 6 Cyl 3.5 L GAS, 6 Cyl 3.9 L FLEX, 6 Cyl 3.9 L GAS
FAQ for Power Steering Hose Repair
Q: How to remove the Power Steering Pump Inlet Pipe?
A:
You can remove the intake manifold cover, and the drive belt, position a drain pan under the vehicle, compress the clamp and disconnect the power steering pump inlet pipe/hose, remove the power steering pump and gear inlet pipe/hoses routing clip nut, the right side engine splash shield, the power steering pump inlet pipe routing bolt, and the power steering pump inlet pipe/hose from the vehicle.
By Bob
GM Specialist
02/11/2022Q: How to install the Power Steering Line/Hose?
A:
You can position the power steering gear inlet pipe/hose, connect the power steering gear inlet pipe/hose fitting, position the steering gear heat shield, install the 2 rear cradle support bolts, remove the jack stand, position the intermediate shaft, the drain pan, install the power steering pump pulley, the drive belt idler pulley, the washer solvent container, the drive belt, the intake manifold cover, and bleed the power steering system.
By Bob
GM Specialist
02/11/2022Q: What is the recommended torque for the power steering pump inlet pipe routing bolt?
A:
The recommended torque is 10 N.m (89 lb in).
By Bob
GM Specialist
02/11/2022Q: How to remove the Power Steering Line/Hose?
A:
You can turn the steering wheel, remove the key, the intake manifold cover, the drive belt, the washer solvent container, the drive belt idler pulley bolt, the 3 bolts and the engine lift bracket, the power steering pulley, the power steering pump and gear inlet pipe/hoses routing clip nut, the power steering gear inlet pipe/hose fitting, the intermediate shaft pinch bolt, the 2 rear cradle support bolts, the 2 power steering gear heat shield bolts, and the power steering gear inlet pipe/hose.
By Bob
GM Specialist
02/11/2022Q: How to remove the Power Steering Cooler Pipe/Hose?
A:
You can turn the steering wheel to the straight forward position, remove the key, remove the right side engine splash shield, place the drain pan under the vehicle, the 2 routing clip retainers, compress the clamp, remove the intermediate shaft pinch bolt and separate the intermediate shaft, the 2 rear cradle support bolts, the 2 power steering gear heat shield bolts and the shield, the cooler pipe/hose fitting, and the cooler pipe/hose.
By Bob
GM Specialist
02/11/2022Q: How to install the Power Steering Cooler Pipe/Hose?
A:
You can position the cooler pipe/hose to the vehicle, connect the cooler pipe/hose fitting to the steering gear, and the steering gear heat shield and install the 2 bolts, remove the drain pan, install the 2 rear cradle support bolts, remove the jack stand, position the intermediate shaft and install the pinch bolt, the right side engine splash shield, the 2 routing clip retainers, and bleed the power steering system.
By Bob
GM Specialist
02/11/2022See more FAQs (1)