< Back ×
My Vehicle Change Vehicle
2007 Buick Terraza
< Back to View All
Alignment Kits
- Department
- Prices
OEM (Genuine) 2007 Buick Terraza Adjust Bolt
PartNumber: 11562165
Product Specifications- Location: Passenger Side; Driver Side
- Other Names: Adjust Bolt, Lower Control Arm Adjust Bolt
- Item Dimensions: 6.0 x 2.4 x 2.0 inches
- Item Weight: 0.70 Pounds
- Fitment Type: Direct Replacement
- Replaces: 10254819
- Part Description: 2007 Buick Terraza Adjust Bolt
Vehicle Fitment- 2007 Buick Terraza | CX, CXL | 6 Cyl 3.5 L GAS, 6 Cyl 3.9 L FLEX, 6 Cyl 3.9 L GAS
$23.30 MSRP:$39.51You Save: $16.21 (42%)
OEM (Genuine) 2007 Buick Terraza Adjust Cam
PartNumber: 10254818
Product Specifications- Location: Passenger Side; Driver Side
- Other Names: Adjust Cam, Lower Control Arm Adjust Cam
- Item Dimensions: 2.3 x 2.2 x 1.1 inches
- Item Weight: 0.50 Pounds
- Fitment Type: Direct Replacement
- Part Description: 2007 Buick Terraza Adjust Cam
Vehicle Fitment- 2007 Buick Terraza | CX, CXL | 6 Cyl 3.5 L GAS, 6 Cyl 3.9 L FLEX, 6 Cyl 3.9 L GAS
$6.43 MSRP:$10.62You Save: $4.19 (40%)
OEM (Genuine) 2007 Buick Terraza Bolt, Rear Axle
PartNumber: 22629930
Product Specifications- Item Dimensions: 5.1 x 3.6 x 2.1 inches
- Item Weight: 1.30 Pounds
- Fitment Type: Direct Replacement
- Part Description: 2007 Buick Terraza Bolt, Rear Axle
Vehicle Fitment- 2007 Buick Terraza | CX, CXL | 6 Cyl 3.5 L GAS, 6 Cyl 3.9 L FLEX, 6 Cyl 3.9 L GAS
FAQ for Camber and Alignment Kit Repair
Q: How to remove the Rear Camber Adjustment?
A:
You can place the vehicle on an alignment machine with rear wheels supported by Weaver plates, loosen the rear lower control arm mounting nuts, adjust the camber with cam bolt, confirm the correct camber value, and check toe alignment and adjust if required.
By Bob
GM Specialist
01/11/2022Q: What is the service and repair procedure for the Rear Toe Adjustment?
A:
The procedure is to loosen the jam nut, adjust the toe to the proper setting by turning the inner link adjustment hex, tighten the jam nut, and recheck the toe alignment.
By Bob
GM Specialist
01/11/2022Q: What should I pay attention to about the Measuring Wheel?
A:
When performing adjustments to vehicles requiring a 4-wheel alignment, set the rear wheel alignment angles first to obtain proper front alignment angles.
By Bob
GM Specialist
01/11/2022Q: What is the service and repair procedure for the Front Toe?
A:
The procedure is to remove the power steering gear seal small clamps, loosen the left and right tie rod jam nuts, rotate the inner tie rods to obtain the proper toe angle of 0 degrees, tighten the tie rod end jam nuts, and install the power steering gear seal small clamps.
By Bob
GM Specialist
01/11/2022Q: How to install the Rear Camber Adjustment?
A:
You can tighten the lower control arm mounting nuts and test drive the vehicle.
By Bob
GM Specialist
01/11/2022Q: What is the service and repair procedure for the Front Camber Adjustment?
A:
The procedure is to remove the tire and wheel, the strut lower bolt to inspect for an oblong strut lower hole, adjust the camber, install the tire and wheel, and lower the vehicle.
By Bob
GM Specialist
01/11/2022Q: What is the service and repair procedure for the Measuring Wheel?
A:
The procedure is to install the alignment equipment according to the manufacturer's instructions, jounce the front and the rear bumpers 3 times before checking the wheel alignment, measure the alignment angles, and record the readings.
By Bob
GM Specialist
01/11/2022Q: What is the recommended torque for the strut lower nut?
A:
The recommended torque is 112 N.m (83 lb-ft).
By Bob
GM Specialist
01/11/2022Q: What is the recommended torque for the nut?
A:
The recommended torque is 62 N.m (45 lb-ft).
By Bob
GM Specialist
01/11/2022Q: What is the recommended torque for the left and right tie rod jam nut?
A:
The recommended torque is 68 N.m (50 lb-ft).
By Bob
GM Specialist
01/11/2022See more FAQs (5)