Notes: Engine Family Number 7GMXB03.9142;CARB Executive Order D-193-143;Certification Level : LEV2 LEV; OE Spec; Cutting & Welding Reqd During Installation
Air Tube: No
Body Type: Spun
Catalytic Converter Body Height: 4"
Catalytic Converter Body Length: 13.25"
Catalytic Converter Body Shape: Round
Catalytic Converter Overall Length: 13.25"
Catalytic Converter Substrate Material: Ceramic
Catalytic Converter Width: 4"
Catalytic Inlet Diameter: 2.25"
Catalytic Outlet Diameter: 2.25"
Catalytic Series: OBDII
Converter Body Material: Stainless Steel
Converter Configuration: Universal Fit
Heat Shield Attached: No
Inlet Attachment: Weld-On
Inlet Orientation: Straight
Inlet Quantity: 1
O2 Sensor Port: No
Outlet Attachment: Weld-On
Outlet Orientation: Straight
Outlet Quantity: 1
Position: Driver Side
Part Description: 2007 Buick Rendezvous OBDII Universal Fit Round Body Catalytic Converter
Notes: Illegal for installation in NY on vehicles equipped w/Calif emission systems; Universal Fit; Fed & Calif Emission systems; Not legal for use in Calif
Catalytic Converter Body Length: 9"
Catalytic Converter Body Shape: Round
Catalytic Converter Overall Length: 15"
Catalytic Inlet Diameter: 2.25"
Catalytic Outlet Diameter: 2.25"
Catalytic Series: OBDII
Converter Body Material: Aluminized Steel
Converter Configuration: Universal Fit
O2 Sensor Port: No
UPC: 841809129710
Part Description: 2007 Buick Rendezvous OBDII Universal Fit Round Body Catalytic Converter
Part Description: 2007 Buick Rendezvous 3Way Catalytic Convertor Assembly (W/ Exhaust Manifold P
More Info
Vehicle Fitment
2007 Buick Rendezvous | CX, CXL | 6 Cyl 3.5 L GAS
FAQ for Catalytic Converter Repair
Q: How to install the catalytic converter?
A:
You need to install the HO2S, the catalytic converter, and a new catalytic converter. Then you can connect the HO2S electrical connector, install the CPA retainer and lower the vehicle.
By Bob
GM Specialist
01/11/2022
Q: How to remove the converter hanger?
A:
You need to raise and support the vehicle. Then you can remove the catalytic converter hanger insulator, the catalytic converter hanger bolts, and the catalytic converter hanger.
By Bob
GM Specialist
01/11/2022
Q: How to remove the catalytic converter?
A:
You need to raise and support the vehicle. After removing the catalytic converter to exhaust manifold nuts and removing the connector position assurance (CPA) retainer, you can disconnect the heated oxygen sensor electrical connector. Then you can remove the catalytic converter, the catalytic converter, the catalytic converter, and the HO2S.
By Bob
GM Specialist
01/11/2022
Q: How to install the converter hanger?
A:
You need to install the catalytic converter hanger, the catalytic converter hanger bolts, and the catalytic converter hanger insulator. Then you can lower the vehicle.
By Bob
GM Specialist
01/11/2022
FAQ for Other Repair Info
Q: How to install the engine oil and oil filter?
A:
After lubricating the new Oil Filter gasket, you can tighten the oil filter and lower the vehicle. Then you need to fill the engine with oil, start the engine and inspect for leaks.
Q: How to install the oil pump?
A:
After installing the Oil Pump, the oil pump bolts, and the case side cover, you can reset the transmission adaptive pressure values.
Q: Can we repair the wiring, connector, or terminals?
A:
No, we cannot repair the wiring, connector, or terminals. We need to replace the Oxygen Sensor if the pigtail wiring, connector, or terminal is damaged.