< Back ×
My Vehicle Change Vehicle
2007 Buick Rendezvous
< Back to View All
Air Bag
- Department
- Prices
OEM (Genuine) 2007 Buick Rendezvous Front Sensor
PartNumber: 10368949
Product Specifications- Location: Driver Side
- Other Names: Front Sensor, Impact Sensor
- Item Dimensions: 3.2 x 2.1 x 2.2 inches
- Item Weight: 0.50 Pounds
- Fitment Type: Direct Replacement
- Replaces: 10343438
- Part Description: 2007 Buick Rendezvous Front Sensor
Vehicle Fitment- 2007 Buick Rendezvous | CX, CX Plus, CXL, CXL Plus, Ultra | 6 Cyl 3.4 L GAS, 6 Cyl 3.5 L GAS, 6 Cyl 3.6 L GAS
$21.46 MSRP:$32.39You Save: $10.93 (34%)OEM (Genuine) 2007 Buick Rendezvous Front Sensor
PartNumber: 10368948Product Specifications- Location: Passenger Side
- Other Names: Front Sensor, Impact Sensor
- Item Dimensions: 3.4 x 3.1 x 3.1 inches
- Item Weight: 0.50 Pounds
- Fitment Type: Direct Replacement
- Replaces: 10343439
- Part Description: 2007 Buick Rendezvous Front Sensor
Vehicle Fitment- 2007 Buick Rendezvous | CX, CX Plus, CXL, CXL Plus, Ultra | 6 Cyl 3.4 L GAS, 6 Cyl 3.5 L GAS, 6 Cyl 3.6 L GAS
OEM (Genuine) 2007 Buick Rendezvous Sensor Asm-Inflator Restraint Side Imp
PartNumber: 10368947
Product Specifications- Location: Driver Side; Passenger Side
- Other Names: Side Impact Sensor, Side Sensor
- Item Dimensions: 3.4 x 3.1 x 3.2 inches
- Item Weight: 0.50 Pounds
- Fitment Type: Direct Replacement
- Part Description: 2007 Buick Rendezvous Sensor Asm-Inflator Restraint Side Imp
Vehicle Fitment- 2007 Buick Rendezvous | CX, CX Plus, CXL, CXL Plus, Ultra | 6 Cyl 3.4 L GAS, 6 Cyl 3.5 L GAS, 6 Cyl 3.6 L GAS
FAQ for Air Bag Sensor Repair
Q: How to remove the inflatable restraint side impact module?
A:
You need to remove the driver seat, the J-clip, the seat back cover, the air bag fasteners, and the retaining clips. Then you can pull the airbag wiring harness up into the seat back and remove the airbag from the seat back frame.
By Bob
GM Specialist
01/11/2022Q: What do you need to do if you have an I/P inflator module?
A:
You need to place the J39401-B in the center of the cleared area and fill the deployment fixture with water or sand. Then you can use the proper nuts and bolts, and mount the I/P module to the deployment fixture. Then, you need to tighten all fasteners that hold the I/P module to the deployment fixture.
By Bob
GM Specialist
01/11/2022Q: How to install the inflatable restraint instrument panel module?
A:
You need to install the inflatable restraint module and the I/P bolts. Then you need to connect the inflatable module connector and install the trim pad to the I/P.
By Bob
GM Specialist
01/11/2022Q: What do you need to pay attention to while steering wheel and I/P inflator modules?
A:
Dual-stage airbag deployments are only used in the steering wheel and I/P inflator modules if the vehicle is equipped. If stage 1 was used to deploy a dual-stage inflator module, stage 2 may still be active. If disposal of a deployed or undeployed dual-stage module is required, both deployment loops must be energized to deploy the airbag.
By Bob
GM Specialist
01/11/2022Q: How to install the inflatable restraint side impact module?
A:
After installing the driver-side airbag, you need to install the airbag fasteners and tighten the fasteners to 10 N.m. Then you need to pull the airbag wiring harness down into the seat cushion, install the harness retaining clips and the seat back cover, and connect the J-clip. Then you can install the driver seat.
By Bob
GM Specialist
01/11/2022Q: How to remove the inflatable restraint instrument panel module?
A:
You need to remove the trim pad from the instrument panel (I/P). Then you can disconnect the inflator module connector. After removing the bolts and the inflatable restraint module, you can fully deploy the module before disposal.
By Bob
GM Specialist
01/11/2022Q: What tools do you need to handle and scrap the inflator module?
A:
You need to have a SIR deployment harness, deployment fixture, side impact module adapter, steering wheel module adapter, I/P module adapter, steering wheel module, and I/P module adapter.
By Bob
GM Specialist
01/11/2022Q: How to remove the inflatable restraint steering wheel module?
A:
After placing the steering wheel, you need to adjust and install J44298 into 2 of the holes. Then you need to push the handle back towards the instrument panel (I/P), release the 2 spring-loaded fasteners, turn the steering wheel, and open J44298. After that, you need to place J44298, pull the driver inflator module gently away from the steering wheel, and remove the connector position assurance (CPA). After that, you need to remove the electrical connector, the horn, the horn contact, the horn contact lead, and the inflatable restraint module. Then you can fully deploy the module before disposal.
By Bob
GM Specialist
01/11/2022Q: How to install the inflatable restraint steering wheel module?
A:
After connecting the horn ground lead and the horn contact lead, you need to rotate the horn contact, connect the inflator module electrical connector and the CPA, and align the driver inflator module fasteners. Then you can push the driver inflator module.
By Bob
GM Specialist
01/11/2022Q: How to remove the inflatable restraint side impact sensor?
A:
After removing the center pillar lower trim and the connector position assurance (CPA), you can disconnect the wiring harness connector, loosen the 2 fasteners, and remove the side impact sensor.
By Bob
GM Specialist
01/11/2022See more FAQs (15)