< Back ×
My Vehicle Change Vehicle
2006 GMC Yukon
< Back to View All
Ignition, Distributors & ECM
- Department
- Brands
- Prices
OEM (Genuine) 2006 GMC Yukon Cylinder & Keys
PartNumber: 15785100
Product Specifications- Notes: All Models; Manual Trans; All
- Item Dimensions: 3.3 x 2.2 x 1.7 inches
- Item Weight: 0.60 Pounds
- Fitment Type: Direct Replacement
- Replaces: 88956845
- Part Description: 2006 GMC Yukon Cylinder & Keys
Vehicle Fitment- 2006 GMC Yukon | Denali, SL, SLE, SLT | 8 Cyl 4.8 L GAS, 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L GAS
$48.49 MSRP:$77.01You Save: $28.52 (38%)
Dorman® Ignition Lock Cylinder for 2006 GMC Yukon
PartNumber: 924-725Product Specifications- Notes: wo/Winged Bezel
- Coding: Coded
- Finish: Black
- Housing Material: Metal
- Installation Hardware Included: No
- Key Programmable: No
- Key Quantity: 2
- Mounting Hardware Included: No
- OE Part Number: 15298923, 88956844
- UPC: 019495354079
- Winged Bezel: No
- Wiring Harness Included: No
- Part Description: 2006 GMC Yukon Ignition Lock Cylinder
Vehicle Fitment- 2006 GMC Yukon | All Trims | All Engines
$34.54
OEM (Genuine) 2006 GMC Yukon Cylinder & Keys
PartNumber: 15298923
Product Specifications- Notes: Yukon & Denali
- Item Dimensions: 3.3 x 2.3 x 1.8 inches
- Item Weight: 0.60 Pounds
- Fitment Type: Direct Replacement
- Replaces: 88956844
- Part Description: 2006 GMC Yukon Cylinder & Keys
Vehicle Fitment- 2006 GMC Yukon | Denali, SL, SLE, SLT | 8 Cyl 4.8 L GAS, 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L GAS
$47.25 MSRP:$99.29You Save: $52.04 (53%)
Original Engine Management® Ignition Lock Cylinder for 2006 GMC Yukon
PartNumber: ILC190Product Specifications- Notes: w/o Acc. Position
- Coding: Coded
- Key Quantity: 2
- Keys Included: Yes
- Mounting Location: Steering Column
- OE Part Number: 15298923
- UPC: 841266086588
- Part Description: 2006 GMC Yukon Ignition Lock Cylinder
Vehicle Fitment- 2006 GMC Yukon | All Trims | All Engines
- 2006 GMC Yukon | All Trims | 8 Cyl 5.3L
FAQ for Ignition Lock Cylinder Repair
Q: What is the removal procedure for the ignition lock cylinder?
A:
You need to disconnect the negative battery cable, disable the SIR system, lower the hush and knee bolster, remove the steering column trim covers, turn the key to the run position, install a wrench into the hole on top of the lock cylinder housing, and slide the lock cylinder out of the lock cylinder housing.
By Bob
GM Specialist
01/11/2022Q: How to assemble and code the IP storage compartment lock cylinder?
A:
You need to hold the cylinder, insert tumbler springs into the 4 spring wells, install the tumbler for key cut position 7 into the slot nearest to the front of the lock cylinder, install the 3 remaining tumblers, key cut positions 8, 9, and 10, into the cylinder, snap the tumblers into place with light hand pressure, and inspect for the correct loading of the tumblers.
By Bob
GM Specialist
01/11/2022Q: What is the removal procedure for the ignition lock cylinder case?
A:
You need to disable the SIR system, remove the ignition switch, the turn signal cancel cam, the park lock cable from the lock cylinder housing, 3 TORX screws, and the lock cylinder housing from the steering column.
By Bob
GM Specialist
01/11/2022Q: What is the recommended torque for the TORX screws?
A:
The recommended torque is 7 Nm (62-inch lbs.).
By Bob
GM Specialist
01/11/2022Q: What is the recommended torque for the TORX(r) screws?
A:
The recommended torque is 7 Nm (62-inch lbs.).
By Bob
GM Specialist
01/11/2022Q: How to install the ignition lock cylinder?
A:
You need to install the key into the lock cylinder, rotate the lock cylinder housing gear clockwise to the start position, align the lock cylinder and install into the lock cylinder housing, install the steering column trim covers, the hush and knee bolster, enable the SIR system, and connect the negative battery cable.
By Bob
GM Specialist
01/11/2022See more FAQs (1)