< Back ×
My Vehicle Change Vehicle
2006 GMC Yukon
< Back to View All
Air Bag
- Department
- Brands
- Prices
OEM (Genuine) 2006 GMC Yukon Side Sensor
PartNumber: 10370151
Product Specifications- Notes: All Models
- Location: Driver Side; Passenger Side
- Other Names: Module, Side Impact Sensor, Side Sensor
- Item Dimensions: 3.2 x 3.2 x 3.1 inches
- Item Weight: 0.70 Pounds
- Fitment Type: Direct Replacement
- Replaces: 15103521
- Part Description: 2006 GMC Yukon Side Sensor
Vehicle Fitment- 2006 GMC Yukon | Denali, SL, SLE, SLT | 8 Cyl 4.8 L GAS, 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L GAS
$187.30 MSRP:$294.58You Save: $107.28 (37%)
OEM (Genuine) 2006 GMC Yukon Front Sensor
PartNumber: 10370149
Product Specifications- Other Names: Front Impact Sensor, Front Sensor
- Item Dimensions: 3.0 x 2.1 x 2.1 inches
- Item Weight: 0.40 Pounds
- Fitment Type: Direct Replacement
- Replaced by: 85597995
- Part Description: 2006 GMC Yukon Front Sensor
Vehicle Fitment- 2006 GMC Yukon | Denali, SL, SLE, SLT | 8 Cyl 4.8 L GAS, 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L GAS
Dorman® OE Solutions Air Bag Impact Sensor for 2006 GMC Yukon
PartNumber: 590-200Product Specifications- Connector Gender: Female
- Connector/Terminal Configuration: 2 Pin
- OE Part Number: 10370149, 15103522
- Package Quantity: 1
- UPC: 019495423560
- Part Description: 2006 GMC Yukon OE Solutions Air Bag Impact Sensor
Vehicle Fitment- 2006 GMC Yukon | All Trims | All Engines
FAQ for Air Bag Sensor Repair
Q: What is the recommended torque for the retaining bolts to the side impact module.?
A:
The recommended torque is 10 Nm (89 lb in).
By Bob
GM Specialist
01/11/2022Q: What is the removal procedure for the inflatable restraint side impact module in the front?
A:
You need to disable the SIR system, remove the front seat, the seat back cover, the retaining bolts, the side impact module retainer, the wiring harness retaining clips, the wiring harness from the seat frame, and the side impact module, fully deploy the module before disposal.
By Bob
GM Specialist
01/11/2022Q: What is the removal procedure for the inflatable restraint front-end sensor?
A:
You need to disable the SIR system, disconnect the electrical connector, and remove the connector position assurance (CPA) from the connector, the sensor bolt, and the sensor.
By Bob
GM Specialist
01/11/2022Q: What is the recommended torque for the sensor horizontally to the radiator support?
A:
The recommended torque is 9 Nm (79 lb in).
By Bob
GM Specialist
01/11/2022Q: What is the removal procedure for the inflatable restraint side impact sensor?
A:
You need to disable the SIR system, remove the front door trim panel, loosen the 2 inflatable restraint side impact sensor fasteners, remove the inflatable restraint side impact sensor from the door, remove the connector position assurance (CPA), and disconnect the inflatable restraint side impact sensor yellow 2-way harness connector.
By Bob
GM Specialist
01/11/2022Q: What is the recommended torque for the fasteners?
A:
The recommended torque is 10 Nm (89 lb in).
By Bob
GM Specialist
01/11/2022Q: How to enable the SIR in Zone 5?
A:
You need to remove the key from the ignition, connect the I/P module yellow 4-way connector, install the CPA to the I/P module yellow 4-way connector and the SIR fuse into the fuse block, turn on the ignition with the engine off, and perform the diagnostic system check.
By Bob
GM Specialist
28/10/2022Q: How to install the repair the fasteners?
A:
You need to remove the stripped nut and discard the nut, drill out the weld spots to the weld stud, remove and discard the stud, condition the floor panel attaching surface where the new stud is to be installed, install new weld stud GM P/N 115115602 and clamp the weld stud, MIG-weld the stud at the drilled holes from above or below the floor pan, apply body sealer around any exposed openings, and install a new fastener GM P/N 11515933.
By Bob
GM Specialist
28/10/2022Q: What should be noticed when disabling the SIR in Zone 2?
A:
With the SIR fuse removed and the ignition ON, the AIR BAG indicator illuminates. This is normal operation and does not indicate a SIR system malfunction.
By Bob
GM Specialist
28/10/2022Q: What is the disabling procedure for the SIR in Zone 6?
A:
You need to turn the steering wheel, turn off the ignition, remove the key from the ignition, the SIR fuse from the fuse block, the RF door trim panel, and the connector position assurance (CPA), and disconnect the side impact sensor yellow 2-way connector.
By Bob
GM Specialist
28/10/2022See more FAQs (17)