< Back ×
My Vehicle Change Vehicle
2006 Chevrolet Colorado
< Back to View All
Driveline, Axles & 4WD
- Department
- Brands
- Prices
OEM (Genuine) 2006 Chevrolet Colorado Universal Joints
PartNumber: 89040245
Product Specifications- Notes: Canyon, Colorado; 1 Piece Drive Shaft; Rear;Canyon, Colorado; 2 Piece Drive Shaft; Rear
- Other Names: Universal Joints
- Item Dimensions: 4.1 x 4.2 x 1.6 inches
- Item Weight: 1.60 Pounds
- Fitment Type: Direct Replacement
- Replaces: 12476136, 15577432, 12543576, 12472402
- Part Description: 2006 Chevrolet Colorado Universal Joints
Vehicle Fitment- 2006 Chevrolet Colorado | Base, LS, LT, Sport, Sport LS, WT, Z71, Z71 LS, Z85, Z85 LS | 4 Cyl 2.8 L GAS, 4 Cyl 2.9 L GAS, 5 Cyl 3.5 L GAS, 5 Cyl 3.7 L GAS, 8 Cyl 5.3 L GAS
$98.05 MSRP:$162.29You Save: $64.24 (40%)
Dorman® OE Solutions Front Propeller Shaft Cv Joint Kit for 2006 Chevrolet Colorado
PartNumber: 932-105Product Specifications- Notes: Propeller Shaft
- Additional Contents: Boot Clamp, Internal Snap Ring
- Bolt Diameter: 0.41"
- Bolt Hole Quantity: 4
- Color/Finish: Natural
- Grease Included: Yes
- Installation Hardware Included: No
- Item Grade: Standard Replacement
- Material: Steel
- Spline Count: 0
- Spline Length (In): 3.5"
- UPC: 019495343141
- Part Description: 2006 Chevrolet Colorado OE Solutions Front Propeller Shaft Cv Joint Kit
Vehicle Fitment- 2006 Chevrolet Colorado | All Trims | All Engines
$133.17OEM (Genuine) 2006 Chevrolet Colorado Universal Joints
PartNumber: 89040243
Product Specifications- Notes: Canyon, Colorado; 1 Piece Drive Shaft; Front;Canyon, Colorado; 2 Piece Drive Shaft; Center;Canyon, Colorado; 2 Piece Drive Shaft; Front
- Other Names: Universal Joints
- Item Dimensions: 4.2 x 4.2 x 1.6 inches
- Item Weight: 1.70 Pounds
- Fitment Type: Direct Replacement
- Replaces: 12473124, 12476135, 12543573
- Part Description: 2006 Chevrolet Colorado Universal Joints
Vehicle Fitment- 2006 Chevrolet Colorado | Base, LS, LT, Sport, Sport LS, WT, Z71, Z71 LS, Z85, Z85 LS | 4 Cyl 2.8 L GAS, 4 Cyl 2.9 L GAS, 5 Cyl 3.5 L GAS, 5 Cyl 3.7 L GAS, 8 Cyl 5.3 L GAS
$98.05 MSRP:$162.29You Save: $64.24 (40%)
FAQ for Cv Joint Repair
Q: What is the proper way to install the wheel drive shaft inner joint and seal?
A:
The proper way is to install the new small retaining clamp onto the neck of the inner seal, place the cage on the table large diameter side up, install the small retaining ring using J 8059 into the groove of the driveshaft bar, and then install 'the inner seal onto the D/O joint housing.
By Bob
GM Specialist
01/11/2022Q: What is the removal procedure for the wheel drive shaft inner joint and seal?
A:
The procedure is to place the driveshaft in a vise, remove the D/O joint housing in the following manner, remove the cage and the inner race assembly from the driveshaft bar, remove the balls, remove the inner race from the cage, and then remove the seal and discard.
By Bob
GM Specialist
01/11/2022Q: What is the proper way to install the wheel drive shaft outer joint and seal?
A:
The proper way is to place the new small retaining clamp onto the outer seal, position the lip of the outer seal into the groove on the CN joint, and then install the inner seal.
By Bob
GM Specialist
01/11/2022Q: What is the removal procedure for the wheel drive shaft outer joint and seal?
A:
The procedure is to remove the inner seal, use a hand grinder to cut through the large retaining clamp located at the CN joint, use a hand grinder to cut through the small retaining clamp on the small end of the outer seal, and then remove the outer seal from the CN joint.
By Bob
GM Specialist
01/11/2022