< Back ×
My Vehicle Change Vehicle
2006 Chevrolet Cobalt
< Back to View All
Wipers & Washers
- Department
- Prices
OEM (Genuine) 2006 Chevrolet Cobalt Nozzle
PartNumber: 20820073
Product Specifications- Location: Driver Side; Passenger Side
- Other Names: Nozzle, Washer Hose, Washer Nozzle
- Item Dimensions: 1.8 x 1.2 x 0.7 inches
- Item Weight: 0.30 Pounds
- Fitment Type: Direct Replacement
- Replaces: 15173510
- Part Description: 2006 Chevrolet Cobalt Nozzle
Vehicle Fitment- 2006 Chevrolet Cobalt | Base, LS, LT, LTZ, Sport, SS | 4 Cyl 2.0 L GAS, 4 Cyl 2.2 L GAS, 4 Cyl 2.4 L GAS
$12.96 MSRP:$23.45You Save: $10.49 (45%)
OEM (Genuine) 2006 Chevrolet Cobalt Hose Asm, Windshield Washer Solvent Container
PartNumber: 19152336
Product Specifications- Other Names: Reservoir Hose
- Item Dimensions: 37.8 x 1.0 x 0.5 inches
- Item Weight: 0.60 Pounds
- Fitment Type: Direct Replacement
- Part Description: 2006 Chevrolet Cobalt Hose Asm, Windshield Washer Solvent Container
Vehicle Fitment- 2006 Chevrolet Cobalt | Base, LS, LT, LTZ, Sport, SS | 4 Cyl 2.0 L GAS, 4 Cyl 2.2 L GAS, 4 Cyl 2.4 L GAS
OEM (Genuine) 2006 Chevrolet Cobalt Hose Asm-Windshield Washer Nozzle
PartNumber: 22694232
Product Specifications- Other Names: Washer Hose
- Item Dimensions: 42.2 x 1.2 x 0.5 inches
- Item Weight: 0.50 Pounds
- Fitment Type: Direct Replacement
- Part Description: 2006 Chevrolet Cobalt Hose Asm-Windshield Washer Nozzle
Vehicle Fitment- 2006 Chevrolet Cobalt | Base, LS, LT, LTZ, Sport, SS | 4 Cyl 2.0 L GAS, 4 Cyl 2.2 L GAS, 4 Cyl 2.4 L GAS
FAQ for Windshield Washer Hose Repair
Q: How to install the hose-windshield washer?
A:
You need to position the washer hose, secure the washer hose to the air inlet grille plenum flange at three locations, route the washer hose down alongside the right front inner fender flange, connect the washer hose fender flange clips to the fender flange, connect the washer hose to the washer pump hose and secure the fender flange clip, install the air inlet grille panel, and close the hood.
By Bob
GM Specialist
01/11/2022Q: What is the removal procedure for the hose-windshield washer?
A:
The procedure is to open the hood, remove the air inlet grille panel, disconnect the washer hose from the washer container hose at the fender flange, disconnect the washer hose from the air inlet grille panel plenum flange, disconnect the fender flange clip from the fender flange, pull the washer hose pump end out alongside the right front inner fender and into the engine compartment, and remove the washer hose.
By Bob
GM Specialist
01/11/2022