< Back ×
My Vehicle Change Vehicle
2005 Chevrolet Classic
< Back to View All
Light Relays, Switches & Control Modules
- Department
- Brands
- Prices
Cardone Reman® Remanufactured Body Control Computer for 2005 Chevrolet Classic
PartNumber: 73-5854Product Specifications- Notes: with OE # 22705854;Units must be flashed ON the vehicle.Vehicle specific on-car programming must be performed AFTER install to prevent drivability issues
- Connector/Terminal Configuration: Pin/Male; Pin/Male; Pin/Male
- Module Housing Material: Plastic
- Product Condition: Remanufactured
- Removable PROM: No
- Terminal Quantity: 24; 24; 16
- Part Description: Remanufactured Body Control Computer
$124.54
OEM (Genuine) 2005 Chevrolet Classic Body Control Module
PartNumber: 22701288
Product Specifications- Notes: All Models
- Other Names: Body Control Module
- Item Dimensions: 10.1 x 6.7 x 3.3 inches
- Item Weight: 0.80 Pounds
- Fitment Type: Direct Replacement
- Replaces: 22684973
- Part Description: Body Control Module
OEM (Genuine) 2005 Chevrolet Classic Body Control Module Assembly
PartNumber: 22705854
Product Specifications- Notes: Body
- Other Names: Control Module
- Item Dimensions: 6.1 x 4.0 x 10.4 inches
- Item Weight: 1.20 Pounds
- Fitment Type: Direct Replacement
- Replaces: 22681080, 9351259, 12206819, 09351259
- Part Description: Body Control Module Assembly
FAQ for Body Control Module Repair
Q: What if a module does not receive a node alive message when expected?
A:
If a module does not receive a node alive message when expected, a DTC will be set.
By Bob
GM Specialist
01/11/2022Q: What should be done before system DTC or symptom diagnosis?
A:
The use of the Diagnostic System Check-Vehicle will identify the correct procedures to begin vehicle diagnosis. These must be performed before system DTC or symptom diagnosis.
By Bob
GM Specialist
01/11/2022Q: How to avoid future misdiagnosis after programming?
A:
Turn the ignition OFF for 10 seconds, connect the scan tool to the data link connector, turn the ignition ON with the engine OFF, use the scan tool to retrieve history DTCs from all modules, and clear all history DTCs.
By Bob
GM Specialist
01/11/2022Q: Will module operations not begin before the system power mode is identified?
A:
Normal vehicle class 2 communications and module operations will not begin until the system power mode has been identified.
By Bob
GM Specialist
01/11/2022Q: What is the removal procedure for the Body Control Module?
A:
Ensure that the ignition switch is in the off position, remove the right sound insulator, remove the body control module, and disconnect the BCM connectors from the BCM.
By Bob
GM Specialist
01/11/2022Q: What is the installation procedure for the Body Control Module?
A:
Connect the BCM connectors to the BCM, install the BCM module, install the right sound insulator, and program the BCM.
By Bob
GM Specialist
01/11/2022Q: What should be done before using the symptom tables?
A:
You should perform the Diagnostic System Check-Vehicle in Vehicle DTC Information before using the symptom tables, and review the system operation to familiarize yourself with the system functions.
By Bob
GM Specialist
01/11/2022Q: Why is there intermittent service lamp illumination?
A:
This condition may be caused by a buildup of nonconductive insulating oxidized debris known as fretting corrosion, occurring between two electrical contact surfaces of the connection or connector.
By Bob
GM Specialist
01/11/2022Q: When will the BCM enter a sleep state?
A:
The BCM will enter a sleep state when all of the following conditions exist: the ignition switch is off. no activity exists on the serial data line. no outputs are commanded. no delay timers are actively counting. and no wake-up inputs are present.
By Bob
GM Specialist
01/11/2022See more FAQs (4)