< Back ×
My Vehicle Change Vehicle
2005 Buick Rainier
< Back to View All
A/C & Heating
- Department
- Brands
- Prices
Dorman® Hvac Control Module for 2005 Buick Rainier
PartNumber: 599-211XDProduct Specifications- Notes: New; w/Auto AC Controls; Auto Configuration Software; New
- Automatic Temperature Control: Yes
- Connector Gender: Female
- Connector Quantity: 2
- Control Type: Automatic
- Housing Color: Black
- Instruction Manual Included: Yes
- Mounting Hardware Included: No
- Mounting Type: Bolt On
- OE Part Number: 10367041, 15133519, 15192450, 15214766, 15832314, 15832316, 15855848, 21997426, 21997427, 10367042, 15105215, 15107730, 15137655, 15185639, 15195564, 15201969, 15222482, 15763065, 15832318, 15855849, 15814152, 15203179, 15220310, 15220319, 10399657, 15105
- Pin Count: 24; 12
- Programming Required: No
- Terminal Gender: Male
- Terminal Quantity: 36
- Terminal Type: Pin
- UPC: 194883000032
- Wire Harness Included: No
- Part Description: 2005 Buick Rainier Hvac Control Module
Vehicle Fitment- 2005 Buick Rainier | All Trims | All Engines
$223.70
Dorman® Hvac Control Module for 2005 Buick Rainier
PartNumber: 599-210XDProduct Specifications- Notes: New; w/Manual AC Controls; Auto Configuration Software; New
- Automatic Temperature Control: No
- Connector Gender: Female
- Connector Quantity: 2
- Control Type: Manual
- Housing Color: Black
- Instruction Manual Included: No
- Mounting Hardware Included: No
- Mounting Type: Bolt On
- OE Part Number: 10370033, 10370034, 10395426, 10395427, 15022101, 15076095, 15076096, 15084170, 15084171, 15086835, 15107752, 15107753, 15132072, 15136888, 15136889, 15165920, 15183792, 15183793, 15189435, 15189436, 15195333, 15195382, 15195383, 15201681, 15203181, 15220
- Pin Count: 24; 7
- Programming Required: No
- Terminal Gender: Male
- Terminal Quantity: 24
- Terminal Type: Pin
- UPC: 194883000025
- Wire Harness Included: No
- Part Description: 2005 Buick Rainier Hvac Control Module
Vehicle Fitment- 2005 Buick Rainier | All Trims | All Engines
$178.90
OEM (Genuine) 2005 Buick Rainier AC Relay
PartNumber: 13500114
Product Specifications- Notes: Fuse Block-Engine Compartment, AC Compressor;Fuse Block-Engine Compartment, Fog Lamp;Fuse Block-Engine Compartment, Front Washer Pump;Fuse Block-Engine Compartment, Fuel Pump;Fuse Block-Engine Compartment, High Beam;Fuse Block-Engine Compartment, Horn;Fuse Block-Engine Compartment, Rear Washer Pump; Fuse Block-Instrument Panel, Park Lamp; All Models
- Item Dimensions: 3.8 x 2.2 x 0.7 inches
- Item Weight: 0.40 Pounds
- Fitment Type: Direct Replacement
- Replaces: 12193606, 19115080, 15328866, 12135034, 15393412, 12088567, 12135170, 19116057
- Part Description: 2005 Buick Rainier AC Relay
Vehicle Fitment- 2005 Buick Rainier | CXL, CXL Plus | 6 Cyl 4.2 L GAS, 8 Cyl 5.3 L GAS
$9.55 MSRP:$20.04You Save: $10.49 (53%)
OEM (Genuine) 2005 Buick Rainier Module, Blower Motor Control
PartNumber: 88892976
Product Specifications- Other Names: Control Module, Module
- Item Dimensions: 3.2 x 2.1 x 2.1 inches
- Item Weight: 0.30 Pounds
- Fitment Type: Direct Replacement
- Part Description: 2005 Buick Rainier Module, Blower Motor Control
Vehicle Fitment- 2005 Buick Rainier | CXL, CXL Plus | 6 Cyl 4.2 L GAS, 8 Cyl 5.3 L GAS
Dorman® HVAC Control Module for 2005 Buick Rainier
PartNumber: 599-210Product Specifications- Notes: New; w/Manual AC Controls; Programmable for Applications w/or wo/Rear Window Defogger; New
- Automatic Temperature Control: No
- Connector Gender: Female
- Connector Quantity: 2
- Housing Color: Black
- Instruction Manual Included: No
- Mounting Hardware Included: No
- Mounting Type: Bolt On
- Package Contents: 1 HVAC Control Module
- Programming Required: No
- Terminal Gender: Male
- Terminal Quantity: 24; 7
- Terminal Type: Pin
- UPC: 037495111140
- Part Description: 2005 Buick Rainier HVAC Control Module
Vehicle Fitment- 2005 Buick Rainier | All Trims | All Engines
FAQ for Hvac Control Module Repair
Q: What is the recommended torque for the blower motor control processor mounting screws?
A:
The recommended torque is 1.9 Nm (17 lb in).
By Bob
GM Specialist
01/11/2022Q: How to program and set up the heat, air ventilation, and cooling (HAVC) Control Module?
A:
Each of the following service procedures may require programming or setup procedures to be performed on the HVAC control module or HVAC actuators. If the HVAC control module is replaced, an automatic re-calibration of all the actuators will occur and no additional procedures are necessary. Otherwise, you should avoid reprogramming the HVAC control module, unless directed by a service procedure, or a service bulletin.
By Bob
GM Specialist
01/11/2022Q: How to remove the Blower Motor Control Processor?
A:
You should remove the right closeout panel, disconnect the electrical connector from the blower motor and the electrical connector from the blower motor control processor and remove the blower motor control processor mounting screws and the blower motor control processor.
By Bob
GM Specialist
01/11/2022Q: How to program and set up the heat, air ventilation, and cooling (HAVC) Control Module- Auxiliary?
A:
Each of the following service procedures may require programming or setup procedures to be performed on the auxiliary HVAC control module or HVAC actuators. If the auxiliary HVAC control module is replaced, no additional procedures are necessary. Otherwise, you should not reprogram the auxiliary HVAC control module, unless directed by a service procedure, or a service bulletin.
By Bob
GM Specialist
01/11/2022Q: How to install the Blower Motor Control Processor?
A:
You should install the blower motor control processor and the blower motor control processor mounting screws, connect the electrical connector to the blower motor control processor and the electrical connector to blower motor and install the right closeout panel.
By Bob
GM Specialist
01/11/2022Q: How to remove the heat, air ventilation, and cooling (HAVC) Control Module - Auxiliary?
A:
You should use a flat-bladed tool to carefully pry out on the top of the HVAC control-auxiliary, remove the HVAC control-auxiliary from the center console/seat, disconnect the electrical connector and remove the HVAC control-auxiliary.
By Bob
GM Specialist
01/11/2022Q: How to remove the Blower Motor Processor - Auxiliary?
A:
You should remove the right rear quarter trim panel and the auxiliary heat, air ventilation, and cooling (HAVC) module, disconnect the electrical connector from the blower motor processor and remove the retaining screws from the blower motor processor and the blower motor processor from the HVAC module.
By Bob
GM Specialist
01/11/2022Q: What is the recommended torque for the HVAC control module retaining screws?
A:
The recommended torque is 1.9 Nm (17 lb-ft).
By Bob
GM Specialist
01/11/2022Q: How to remove the heat, air ventilation, and cooling (HAVC) Control Module?
A:
You should remove the instrument panel (I/P) accessory trim plate and the control module retaining screws, depress the HVAC control module retaining tabs, remove the HVAC control module from the instrument panel and then disconnect the electrical connectors from the HVAC control module.
By Bob
GM Specialist
01/11/2022Q: How to install the heat, air ventilation, and cooling (HAVC) Control Module - Auxiliary?
A:
You should connect the HVAC control-auxiliary electrical connector, install the HVAC control-auxiliary in the console bottom first and push in at the top of the HVAC control-auxiliary to engage the HVAC control-auxiliary in the console/seat.
By Bob
GM Specialist
01/11/2022See more FAQs (6)