< Back ×
My Vehicle Change Vehicle
2004 Buick Rendezvous
< Back to View All
Air Filters & Intake Systems
- Department
- Brands
- Prices
OEM (Genuine) 2004 Buick Rendezvous Throttle Body
PartNumber: 12571081
Product Specifications- Notes: Aztek, Rendezvous; 3.6l
- Item Dimensions: 6.9 x 6.0 x 1.2 inches
- Item Weight: 1.20 Pounds
- Replaced by: 19368130
- Part Description: 2004 Buick Rendezvous Throttle Body
Vehicle Fitment- 2004 Buick Rendezvous | CXL, Ultra | 6 Cyl 3.6 L GAS
$56.92 MSRP:$107.42You Save: $50.50 (48%)
Cardone Reman® Remanufactured Throttle Body for 2004 Buick Rendezvous
PartNumber: 67-3016Product Specifications- Notes: Relearn procedure may need to be performed upon installation of unit. Please refer to the service manual for vehicle specific instructions.;with I.D. # 12589056;Harness Connector w/In-Line Pins
- Gaskets Included: No Gasket Required
- Housing Color/Finish: Gray/Unfinished
- Housing Material: Aluminum
- Product Condition: Remanufactured
- Throttle Body Actuation Type: Electric
- Throttle Body Inlet Shape: Round
- Throttle Body Outlet Shape: Round
- Throttle Position Sensor Included: Yes
- Part Description: 2004 Buick Rendezvous Remanufactured Throttle Body
Vehicle Fitment- 2004 Buick Rendezvous | All Trims | 6 Cyl 3.6L
$100.90
Cardone Reman® Remanufactured Throttle Body for 2004 Buick Rendezvous
PartNumber: 67-3048Product Specifications- Notes: Relearn procedure may need to be performed upon installation of unit. Please refer to the service manual for vehicle specific instructions.;with I.D. # 12571081;Harness Connector w/Off-Set Pins
- E-Waste: Yes
- Housing Color/Finish: Gray /Unfinished
- Housing Material: Aluminum
- Idle Air Control Motor Included: No
- Package Contents: ETB, Instruction sheet
- Product Condition: Remanufactured
- Throttle Body Actuation Type: Electric
- Throttle Body Inlet Shape: Round
- Throttle Body Outlet Shape: Round
- Throttle Position Sensor Included: Yes
- UPC: 884548287082
- Part Description: 2004 Buick Rendezvous Remanufactured Throttle Body
Vehicle Fitment- 2004 Buick Rendezvous | All Trims | 6 Cyl 3.6L
OEM (Genuine) 2004 Buick Rendezvous Throttle Body Assembly
PartNumber: 12595275
Product Specifications- Notes: Aztek, Rendezvous; 3.4l
- Other Names: Throttle Body
- Item Dimensions: 7.8 x 5.7 x 5.9 inches
- Item Weight: 2.10 Pounds
- Fitment Type: Direct Replacement
- Replaces: 17113631
- Part Description: 2004 Buick Rendezvous Throttle Body Assembly
Vehicle Fitment- 2004 Buick Rendezvous | CX, CX Plus, CXL, CXL Plus | 6 Cyl 3.4 L GAS
FAQ for Throttle Body Repair
Q: How to remove the Accelerator Controls Cable?
A:
You need to remove the accelerator cable shield, disconnect the accelerator cable from the throttle body lever, then disconnect the accelerator cable from the accelerator cable bracket, remove the left instrument panel sound insulator, then disconnect the accelerator cable from the accelerator pedal, and squeeze the accelerator cable cover tangs and push the accelerator cable through the bulkhead, finally remove the accelerator cable.
By Bob
GM Specialist
02/11/2022Q: What is the recommended torque for the throttle body retaining nuts and bolts?
A:
The recommended torque is 28 N.m (21 lb-ft).
By Bob
GM Specialist
02/11/2022Q: What is the proper way to install the Accelerator Controls Cable Bracket?
A:
You should position the accelerator cable bracket on the throttle body, then install the nut and bolts, connect the cruise control cable to the accelerator cable bracket, connect the accelerator cable to the throttle body lever, and connect the cruise control cable to the throttle lever and accelerator bracket.
By Bob
GM Specialist
02/11/2022Q: How to clean the Throttle Body?
A:
You need to remove the air cleaner outlet duct, remove the air inlet screen if applicable, next inspect the throttle body bore and the throttle valve plate for deposits, remove and disassemble the throttle body for cleaning if the deposits are excessive, then assemble and install the throttle body, install the air inlet screen if applicable and the air cleaner outlet duct.
By Bob
GM Specialist
02/11/2022Q: How to remove the Accelerator Controls Cable Bracket?
A:
You need to disconnect the accelerator cable cross slug from the throttle body lever, disconnect the accelerator cable from the accelerator cable bracket, disconnect the cruise control cable from the throttle lever and accelerator bracket, then remove the nut and bolts holding the accelerator cable bracket to the throttle body, and remove the accelerator cable bracket.
By Bob
GM Specialist
02/11/2022Q: What is the recommended torque for the idle air control valve attaching screws?
A:
The recommended torque is 3.0 Nm (27 lb in).
By Bob
GM Specialist
01/11/2022Q: How do you disassemble the idle air control valve?
A:
You can remove the throttle control cable bracket from the throttle body, remove the canister purge solenoid valve, disconnect the idle air control electrical connector, remove the idle air control valve attaching screws, remove the idle air control valve and remove the idle air control valve o-ring.
By Bob
GM Specialist
01/11/2022See more FAQs (2)