< Back ×
My Vehicle Change Vehicle
2004 Buick Rendezvous
< Back to View All
Door Handles, Locks & Related Parts
- Department
- Prices
OEM (Genuine) 2004 Buick Rendezvous Gate Asm, Lift
PartNumber: 88956104
Product Specifications- Other Names: Lift Gate
- Item Dimensions: 61.7 x 14.4 x 55.0 inches
- Item Weight: 56.10 Pounds
- Fitment Type: Direct Replacement
- Replaces: 88954962
- Part Description: 2004 Buick Rendezvous Gate Asm, Lift
Vehicle Fitment- 2004 Buick Rendezvous | CX, CX Plus, CXL, CXL Plus, Ultra | 6 Cyl 3.4 L GAS, 6 Cyl 3.5 L GAS, 6 Cyl 3.6 L GAS
FAQ for Liftgates Repair
Q: What is the proper way to install the liftgate window (Pontiac)?
A:
You should install a stationary window into the opening, install the liftgate window and frame to the vehicle, install the rear spoiler, install the liftgate trim, then remove the double layer of masking tape around the perimeter of the painted surfaces and the interior trim, and close the liftgate.
By Bob
GM Specialist
01/11/2022Q: What is the proper way to install the liftgate window (Buick)?
A:
You should install a stationary window into the opening, connect the rear liftgate window defogger connectors to the right and left sides, install the center light applique, install the rear wiper motor, then remove the double layer of masking tape around the perimeter of the painted surfaces and the interior trim, and close the liftgate.
By Bob
GM Specialist
01/11/2022Q: How to remove the liftgate window (Buick)?
A:
You need to remove the rear wiper motor, and the center light applique, disconnect the rear liftgate window defogger connectors from the right and the left sides, then tape off and protect the inner edges of the rear window defogger grid lines from the window removal tool, separate the urethane adhesive from the window, and remove the liftgate window from the liftgate. Place the liftgate window face up on a soft protective cover.
By Bob
GM Specialist
01/11/2022Q: What is the proper way to install the handle?
A:
The proper way is to install the endgate handle to the endgate handle assembly, install the bolts to the endgate handle and close the endgate.
By Bob
GM Specialist
01/11/2022Q: How to install the Trim Panel-Endgate?
A:
You should install the new trim panel retainers to the endgate trim panel, align the endgate trim panel to the endgate inner panel, install the endgate trim panel, then install the endgate inside handle to the endgate, and close the endgate.
By Bob
GM Specialist
01/11/2022Q: What is the proper way to install the Trim Panel-Liftgate (Aztek)?
A:
You should install the upper liftgate trim panel to the liftgate by pressing down until fully seated, position the defogger harness to the cutout in the upper trim panel, install the right and the left side upper trim panel by pressing in until seated, install the lower trim panels, then install the right and left sides of the lower trim panels, and close the liftgate.
By Bob
GM Specialist
01/11/2022Q: What is the recommended torque for the endgate handle bolts?
A:
The recommended torque is 10 Nm (89 lb in).
By Bob
GM Specialist
01/11/2022Q: What is the proper way to install the Water Deflector-Endgate?
A:
You should align the endgate door water deflector to the endgate inner panel, secure the water deflector at the corners, then press the adhesive outward and upward to prevent puckering, and install the endgate trim panel.
By Bob
GM Specialist
01/11/2022Q: How to remove the Trim Panel-Liftgate (Rendezvous)?
A:
You need to raise the lift gate, remove the access trim panel from the liftgate, then remove 2 screws from the bottom of the trim panel, use J 38778 to disengage the fasteners from the trim panel, and remove the trim panel.
By Bob
GM Specialist
01/11/2022Q: What is the proper way to install the Trim Panel-Liftgate (Rendezvous)?
A:
You should install the trim panel to the lift gate, install new fasteners to the trim panel, install the screws to the bottom of the trim panel, install the access trim panel to the lift gate, and close the lift gate.
By Bob
GM Specialist
01/11/2022See more FAQs (10)