< Back ×
My Vehicle Change Vehicle
2004 Buick Rendezvous
< Back to View All
Air Bag
- Department
- Prices
OEM (Genuine) 2004 Buick Rendezvous Sensor Asm-Inflator Restraint Front End Discriminating
PartNumber: 10339759
Product Specifications- Location: Passenger Side
- Other Names: Front Sensor, Impact Sensor
- Item Dimensions: 3.4 x 3.2 x 3.1 inches
- Item Weight: 0.50 Pounds
- Fitment Type: Direct Replacement
- Part Description: 2004 Buick Rendezvous Sensor Asm-Inflator Restraint Front End Discriminating
Vehicle Fitment- 2004 Buick Rendezvous | CX, CXL, Ultra | 6 Cyl 3.4 L GAS, 6 Cyl 3.6 L GAS
OEM (Genuine) 2004 Buick Rendezvous Sensor Asm-Inflator Restraint Side Imp
PartNumber: 10317558
Product Specifications- Location: Driver Side; Passenger Side
- Other Names: Side Impact Sensor, Side Sensor
- Item Dimensions: 4.4 x 2.2 x 2.2 inches
- Item Weight: 0.70 Pounds
- Fitment Type: Direct Replacement
- Part Description: 2004 Buick Rendezvous Sensor Asm-Inflator Restraint Side Imp
Vehicle Fitment- 2004 Buick Rendezvous | CX, CX Plus, CXL, CXL Plus, Ultra | 6 Cyl 3.4 L GAS, 6 Cyl 3.6 L GAS
OEM (Genuine) 2004 Buick Rendezvous Sensor Asm-Inflator Restraint Front End Discriminating
PartNumber: 10338914Product Specifications- Location: Driver Side
- Other Names: Front Sensor, Impact Sensor
- Item Dimensions: 3.4 x 3.1 x 3.1 inches
- Item Weight: 0.50 Pounds
- Fitment Type: Direct Replacement
- Part Description: 2004 Buick Rendezvous Sensor Asm-Inflator Restraint Front End Discriminating
Vehicle Fitment- 2004 Buick Rendezvous | CX, CXL, Ultra | 6 Cyl 3.4 L GAS, 6 Cyl 3.6 L GAS
FAQ for Air Bag Sensor Repair
Q: What is the recommended torque for the airbag fasteners?
A:
The recommended torque is 10 N.m (89 lb in).
By Bob
GM Specialist
01/11/2022Q: How many wires does the steering wheel module have?
A:
If the vehicle is equipped with dual-stage airbags, the steering wheel module and I/P module will each have 4 wires and the standard airbags will only have 2 wires.
By Bob
GM Specialist
01/11/2022Q: What components should be replaced after a collision involving airbag deployment?
A:
You need to replace the inflatable restraint I/P module, inflatable restraint steering wheel module, inflatable restraint sensing and diagnostic module (SDM), inflatable restraint PPS, Rendezvous only, inflatable restraint front end sensor, Left/Right, Rendezvous only, and inflatable restraint seat belt retractor pretensioner, Left/Right, Rendezvous only.
By Bob
GM Specialist
01/11/2022Q: What special tool will I need when servicing the inflatable restraint steering wheel module?
A:
You will need a driver airbag removal tool.
By Bob
GM Specialist
01/11/2022Q: What is the proper way to install the LH inflatable restraint side impact module?
A:
You should install the driver-side airbag to the seat while guiding the airbag wiring harness through the trim cup, install the airbag fasteners, pull the airbag wiring harness down into the seat cushion while guiding the harness through the wire triangle of the seat frame, then install the harness retaining clips to the seat frame, install the seat back cover, and connect the J-clip that is along the lower rear seat back, install the driver seat, and enable the SIR system.
By Bob
GM Specialist
01/11/2022Q: What should be disabled when servicing the inflatable restraint steering wheel module?
A:
You should disable the SIR system before servicing the inflatable restraint steering wheel module.
By Bob
GM Specialist
01/11/2022Q: What is the proper way to install the inflatable restraint front-end sensor?
A:
You should remove any dirt, grease, and other contaminants from the mounting surface, connect the sensor harness connector to the sensor, install the orange CPA into the yellow sensor harness connector, position the sensor on the upper radiator core support, and point the arrow on the sensor toward the front of the vehicle, install the sensor bolts, secure the fascia to the radiator support, install the retainers that hold the upper front bumper fascia to the radiator support, install the grille, finally enable the SIR system.
By Bob
GM Specialist
01/11/2022Q: How to remove the inflatable restraint front-end sensor?
A:
You need to disable the SIR system, remove the grille, remove the retainers that hold the upper front bumper fascia to the radiator support, pull the fascia from the radiator support to gain access to the sensor bolts, then remove the orange connector position assurance (CPA) from the yellow sensor harness connector, disconnect the harness connector from the sensor, remove the sensor bolts, remove the sensor from the upper radiator core support.
By Bob
GM Specialist
01/11/2022Q: What is the disabling procedure for the SIR?
A:
You should turn the steering wheel so that the vehicle's wheels are pointing straight ahead, turn off the ignition, remove the key from the ignition switch, remove the console accessory wiring junction block access hole cover, remove the sir fuse, remove the connector position assurance and disconnect the harness connector.
By Bob
GM Specialist
28/10/2022Q: What is the enabling procedure for the SIR?
A:
You should remove the key from the ignition, connect the harness connector to the front-end sensor, install the CPA to the front-end sensor harness connector, install the sir fuse and install the console accessory wiring junction block access hole cover.
By Bob
GM Specialist
28/10/2022See more FAQs (7)