< Back ×
My Vehicle Change Vehicle
2002 Buick Regal
< Back to View All
Brake Boosters & Brake Master Cylinders
- Department
- Series
- Brands
- Prices
Centric® Premium Brake Master Cylinder for 2002 Buick Regal
PartNumber: 130.62111Product Specifications- UPC: 805890008392
- Part Description: 2002 Buick Regal Premium Brake Master Cylinder
Vehicle Fitment- 2002 Buick Regal | All Trims | All Engines
$63.05
OEM (Genuine) 2002 Buick Regal Cylinder Asm, Brake Master
PartNumber: 19209260
Product Specifications- Notes: W/O 4 Wheel Disc
- Other Names: Master Cylinder
- Item Dimensions: 9.4 x 7.5 x 9.4 inches
- Item Weight: 2.60 Pounds
- Fitment Type: Direct Replacement
- Replaces: 18026277, 18060780
- Part Description: 2002 Buick Regal Cylinder Asm, Brake Master
Vehicle Fitment- 2002 Buick Regal | GS, GSE, LS, LSE | 6 Cyl 3.8 L GAS
Cardone Reman® Remanufactured Master Cylinder for 2002 Buick Regal
PartNumber: 10-2714Product Specifications- Notes: Supplied w/o Reservoir
- Bore Diameter (N): 1.00"
- E-Waste: No
- Installation Hardware Included: No
- Master Cylinder Color/Finish: Gray
- Master Cylinder Material: Aluminum
- Mounting Hole Quantity: 2
- Package Contents: Master Cylinder, Reservoir Pin Kit
- Port Quantity: 2
- Primary Port Size: M12 x 1.0
- Product Condition: Remanufactured
- Reservoir Included: No
- Secondary Port Size: M12 x 1.0
- UPC: 082617378109
- Part Description: 2002 Buick Regal Remanufactured Master Cylinder
Vehicle Fitment- 2002 Buick Regal | All Trims | All Engines
FAQ for Brake Master Cylinder Repair
Q: How to install the master cylinder?
A:
You need to bench bleed the master cylinder, install the master cylinder and the master cylinder mounting nuts, remove the plugs from the brake pipes, connect the brake pipes to the master cylinder and the electrical connector to the brake fluid level sensor, and bleed the brake system.
By Bob
GM Specialist
01/11/2022Q: What is the removal procedure for the master cylinder fluid level sensor?
A:
You need to disconnect the electrical connector from the brake fluid level sensor, remove the brake fluid level sensor, depress the retaining tabs on the end of the brake fluid level sensor, and press the sensor through the reservoir to remove it.
By Bob
GM Specialist
01/11/2022Q: What is the procedure for master cylinder bench bleeding?
A:
You need to secure the mounting flange of the brake master cylinder, remove the master cylinder reservoir cap and diaphragm, install suitable fittings and transparent hose, route the hoses, fill the master cylinder reservoir, ensure that the ends of the transparent hoses are fully submerged in the brake fluid, depress and release the primary piston, depress and release the primary piston, remove the transparent hoses, install the master cylinder reservoir cap and diaphragm, and remove the fittings and master cylinder.
By Bob
GM Specialist
01/11/2022Q: What is the procedure for the master cylinder reservoir filling?
A:
You need to visually inspect the brake fluid level, inspect the brake system for wear and possible brake fluid leaks if the brake fluid level is at or below the half-full point, and clean the outside of the reservoir on and around the reservoir cap before removing the cap and diaphragm if the brake fluid is to be added to the master cylinder reservoir.
By Bob
GM Specialist
01/11/2022Q: How to install the master cylinder reservoir?
A:
You need to inspect the reservoir, clean the reservoir, dry the reservoir, lubricate the new seals and the outer surface area, install the lubricated seals and the reservoir, tap the reservoir retaining pins into place, place the brake fluid level sensor into the reservoir, press into place to secure the sensor retaining tabs, remove the master cylinder, and install the master cylinder.
By Bob
GM Specialist
01/11/2022Q: What is the disassembly procedure for the master cylinder overhaul?
A:
You need to remove the brake master cylinder, secure the mounting flange of the brake master cylinder, clean the outside of the master cylinder reservoir, remove the reservoir cap and diaphragm, inspect the reservoir cap and diaphragm, remove the master cylinder reservoir, depress the primary piston and remove the piston retainer, remove the primary piston assembly, plug the cylinder inlet ports and the rear outlet ports, remove the secondary piston, the return spring, and discard the primary piston assembly, the piston retainer, and the seals and seal retainer.
By Bob
GM Specialist
01/11/2022Q: What conditions should we inspect the reservoir cap and diaphragm?
A:
The cuts or cracks, and nicks or deformation.
By Bob
GM Specialist
01/11/2022Q: What is the removal procedure for the master cylinder?
A:
You need to disconnect the electrical connector from the brake fluid level sensor and the brake pipes from the master cylinder, plug the open brake pipe ends, remove the master cylinder mounting nuts and the master cylinder, and drain the master cylinder reservoir of all brake fluid.
By Bob
GM Specialist
01/11/2022Q: What should be noticed when adding fluid to the brake master cylinder reservoir?
A:
When adding fluid to the brake master cylinder reservoir, you should use only Delco Supreme II brake fluid from a clean, sealed brake fluid container.
By Bob
GM Specialist
01/11/2022Q: How to install the master cylinder fluid level sensor?
A:
You need to place the brake fluid level sensor into the reservoir, press it into place to secure the sensor retaining tabs, and connect the electrical connector to the brake fluid level sensor.
By Bob
GM Specialist
01/11/2022See more FAQs (6)