Contact Us Live Chat or 1-888-220-8330
Search Bar
Search by Part Number or Keywords
  • My Garage
  • My Account
  • Cart
  • Body & Mirrors
  • Chassis & Brakes
  • Engine & Drivetrain
  • Electrical & Lighting
Help Center
< Back ×
  • Body & Mirrors
  • Chassis & Brakes
  • Engine & Drivetrain
  • Electrical & Lighting
Login/Register My Account Track Order Help Center Contact Us
Replacement and OEM Parts for 2002 Buick Regal Air Intake Hose

2002 Buick Regal Air Intake Hose

My Vehicle Change Vehicle
2002 Buick Regal
Change Vehicle
Vehicle Options
We need more information about your vehicle to make a correct determination of fitment
< Back to View All
Air Filters & Intake Systems
  • Department
  • Prices

1 Product found

2 Q&A for Air Intake Hose Repair
Show Item:
  • 30
  • 60
  • 90
Sort by:
Recommended
Filter
Sort
View by
  • OEM 2002 Buick Regal Duct Asm-Rear Intake Air Diagram - 24507362
    View Related Parts

    OEM (Genuine) 2002 Buick Regal Duct Asm-Rear Intake Air

    PartNumber: 24507362
    OEM 2002 Buick Regal Duct Asm-Rear Intake Air - 24507362
    Product Specifications
    • Notes: 1999-04 W/O Supercharger; 1999-04 W/Supercharger
    • Other Names: Inlet Duct, Outlet Duct
    • Item Dimensions: 8.1 x 6.1 x 5.7 inches
    • Item Weight: 1.30 Pounds
    • Fitment Type: Direct Replacement
    • Part Description: 2002 Buick Regal Duct Asm-Rear Intake Air
    More Info
    Vehicle Fitment
    • 2002 Buick Regal | GS, GSE, LS, LSE | 6 Cyl 3.8 L GAS

FAQ for Air Intake Hose Repair

Q: What is the removal procedure for the air cleaner intake duct?
A:
You need to disconnect the IAT sensor electrical connector, remove the IAT sensor, loosen the air cleaner intake duct clamp, and remove the air cleaner intake duct and the air cleaner intake duct from the throttle body.
By Bob
GM Specialist
01/11/2022
Q: How to install the air cleaner intake duct?
A:
You need to install the air cleaner intake duct to the throttle body, the air cleaner intake duct to the air cleaner cover, and the IAT sensor, and connect the IAT sensor electrical connector.
By Bob
GM Specialist
01/11/2022

FAQ for Other Repair Info

Q: What is the removal procedure for the manifold pressure/vacuum sensor?
A:
You need to remove the fuel injector sight shield, disconnect the MAP Sensor electrical connector, carefully release the locking tabs holding the MAP sensor to the PCV valve cover, and pull the MAP sensor straight out of the PCV valve cover.
Q: What is the removal procedure for the lower intake manifold(L36)?
A:
You need to remove the upper Intake Manifold, the generator brace, the drive belt tensioner, the heater water bypass inlet pipe, the EGR outlet pipe, and the radiator inlet hose, disconnect the ECT sensor electrical connector, remove the generator brace bracket bolts, the generator brace bracket, the evaporative emissions canister purge solenoid valve, the lower intake manifold bolts, the lower intake manifold, the lower intake manifold seals and the lower intake manifold gaskets, and clean the lower intake manifold mating surfaces and the intake manifold bolts and bolt holes of the adhesive compound.
Q: What should be noticed when installing the accelerator controls cable?
A:
You should not route flexible components (hoses, wires, conduits, etc.) within 50 mm (2 in) of moving parts unless flexible components can be securely fastened.