< Back ×
My Vehicle Change Vehicle
2002 Buick Park Avenue
< Back to View All
Steering Racks & Gearboxes
- Department
- Prices
OEM (Genuine) 2002 Buick Park Avenue Gear Kit, Steering (Remanufacture)
PartNumber: 19330449
Product Specifications- Notes: W/Variable Assist; Park Avenue; W/Variable Speed
- Other Names: Gear Assembly, Steering Gear
- Item Dimensions: 51.3 x 11.4 x 6.0 inches
- Item Weight: 21.20 Pounds
- Fitment Type: Direct Replacement
- Replaces: 26086925, 26087398, 19169231, 26099974, 26097079, 26098491
- Part Description: 2002 Buick Park Avenue Gear Kit, Steering (Remanufacture)
Vehicle Fitment- 2002 Buick Park Avenue | Base, Ultra | 6 Cyl 3.8 L GAS
OEM (Genuine) 2002 Buick Park Avenue Gear Kit, Steering (Remanufacture)
PartNumber: 19330450
Product Specifications- Notes: W/O Variable Assist; Park Avenue; W/O Variable Speed
- Other Names: Gear Assembly, Steering Gear
- Item Dimensions: 6.3 x 51.9 x 11.7 inches
- Item Weight: 23.50 Pounds
- Fitment Type: Direct Replacement
- Replaces: 26087416, 19153559, 26099975
- Part Description: 2002 Buick Park Avenue Gear Kit, Steering (Remanufacture)
Vehicle Fitment- 2002 Buick Park Avenue | Base, Ultra | 6 Cyl 3.8 L GAS
FAQ for Steering Gearbox Repair
Q: What is the recommended torque for the intermediate shaft lower pinch bolt?
A:
The recommended torque is 47 Nm (35 ft. lbs.).
By Bob
GM Specialist
01/11/2022Q: What kind of special tools will be required when serving the rack and pinion boot-on vehicle?
A:
J22610 Keystone Clamp Plier.
By Bob
GM Specialist
01/11/2022Q: What is the recommended torque for the adjuster plug lock nut?
A:
The recommended torque is 68 Nm (50 ft. lbs.).
By Bob
GM Specialist
01/11/2022Q: How to adjust the rack and pinion gear rack bearing preload-off vehicle (quiet valve)?
A:
You need to loosen the adjuster plug lock nut, turn the adjuster plug clockwise until the adjuster plug bottoms in the gear assembly, then turn the adjuster plug back 50 degrees to 70 degrees, and install the adjuster plug lock nut to the adjuster plug.
By Bob
GM Specialist
01/11/2022Q: How to disassemble the rack and pinion boot-off vehicle?
A:
You need to remove the outer tie rod, remove the hex jam nut from the inner tie rod assembly, remove the tie rod end clamp from the rack and pinion boot, remove the boot clamp from the rack and pinion boot with side cutters, then discard the boot clamp, and remove the rack and pinion boot from the rack and pinion gear assembly.
By Bob
GM Specialist
01/11/2022Q: What is the recommended torque for the cylinder end fittings?
A:
The recommended torque is 27 Nm (20 ft. lbs.).
By Bob
GM Specialist
01/11/2022Q: What is the recommended torque for the power steering gear heat shield retaining bolts?
A:
The recommended torque is 9 Nm (79-inch lbs.).
By Bob
GM Specialist
01/11/2022Q: What is the recommended torque for the outer tie rod nuts?
A:
The recommended torque is 75 Nm (55 ft. lbs.).
By Bob
GM Specialist
01/11/2022Q: What kind of special tools will be required when serving the rack and pinion boot-off vehicle?
A:
J22610 Keystone Clamp Pliers.
By Bob
GM Specialist
01/11/2022Q: What kind of special tools will be required when serving the steering gear stub shaft seals and bearing-off vehicle?
A:
J29810 Stub Shaft Seal Protector.
By Bob
GM Specialist
01/11/2022See more FAQs (12)