< Back ×
My Vehicle Change Vehicle
2001 GMC Yukon XL 1500
< Back to View All
Light Relays, Switches & Control Modules
- Department
- Brands
- Prices
Cardone Reman® Remanufactured Body Control Computer for 2001 GMC Yukon XL 1500
PartNumber: 73-2994FProduct Specifications- Notes: with BCM Code CSPX;Units must be flashed ON the vehicle.Vehicle specific on-car programming must be performed AFTER install to prevent drivability issues
- Connector/Terminal Configuration: Pin/Male; Pin/Male; Pin/Male
- Module Housing Material: Plastic
- Product Condition: Remanufactured
- Removable PROM: No
- Terminal Quantity: 24; 24; 16
- Part Description: 2001 GMC Yukon XL 1500 Remanufactured Body Control Computer
Vehicle Fitment- 2001 GMC Yukon XL 1500 | All Trims | All Engines
$88.06Cardone Reman® Remanufactured Body Control Computer for 2001 GMC Yukon XL 1500
PartNumber: 73-2990FProduct Specifications- Notes: RPO Configuration/Set-Up And Theft Relearn Is Required After Installation;with BCM Code 5899;Units must be flashed ON the vehicle.Vehicle specific on-car programming must be performed AFTER install to prevent drivability issues
- Connector/Terminal Configuration: Pin/Male; Pin/Male; Pin/Male
- Module Housing Material: Plastic
- Product Condition: Remanufactured
- Removable PROM: No
- Terminal Quantity: 24; 24; 16
- Part Description: 2001 GMC Yukon XL 1500 Remanufactured Body Control Computer
Vehicle Fitment- 2001 GMC Yukon XL 1500 | All Trims | All Engines
$84.16
OEM (Genuine) 2001 GMC Yukon XL 1500 Rear Object Alarm Module
PartNumber: 15187264
Product Specifications- Notes: Reverse Sensing System
- Other Names: Module
- Item Dimensions: 5.8 x 5.7 x 3.4 inches
- Item Weight: 0.70 Pounds
- Fitment Type: Direct Replacement
- Replaces: 15068175
- Part Description: 2001 GMC Yukon XL 1500 Rear Object Alarm Module
Vehicle Fitment- 2001 GMC Yukon XL 1500 | Denali, SL, SLE, SLT | 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L GAS
FAQ for Body Control Module Repair
Q: What kind of tools will be required while servicing the SIR/SRS wire?
A:
The tools required include J 38125-B Terminal Repair Kit.
By Bob
GM Specialist
01/11/2022Q: What steps should you take if the voltage is present on only the inputs specified for the ignition switch position?
A:
The proper way is to hold the ignition switch in the position that indicated the incorrect power mode and test the PMM ignition switch inputs for voltage.
By Bob
GM Specialist
01/11/2022Q: What will display for the auto-learn timer?
A:
The scan tool displays the seconds used by the BCM to learn valid code from the Passlock(TM) sensor. The learning procedure consists of 3 consecutive periods.
By Bob
GM Specialist
01/11/2022Q: What steps should you take if the displayed power mode parameter matches the actual ignition switch position?
A:
The steps are to turn ON the ignition with the engine OFF and observe the Class 2 Power Mode parameter under the Diagnostic Circuit Check menu.
By Bob
GM Specialist
01/11/2022Q: How to remove the body control module?
A:
The proper way is to disconnect the negative battery cable(s), remove the knee bolster, disconnect the brown connector and all other connectors, and remove the BCM from the sliding bracket.
By Bob
GM Specialist
01/11/2022Q: What will display when the ambient light sensor voltage is in different volts?
A:
The scan tool displays LIGHT when the ambient light sensor voltage is between 2.2-4.7 volts. The scan tool displays DARK when the ambient light sensor voltage is between 0.2-1.3 volts.
By Bob
GM Specialist
01/11/2022Q: What should be noticed before servicing the body control module?
A:
You must not clear the DTCs unless directed to do so by the service information provided for each diagnostic procedure. All of the diagnostic data that was saved along with the DTC which may be helpful for some diagnostic procedures will be erased from the memory when the DTCs are cleared.
By Bob
GM Specialist
01/11/2022Q: What will display for door lock relay feedback?
A:
The scan tool displays the state of the door lock relay. The scan tool displays ON when the BCM senses the door lock relay coil is energized.
By Bob
GM Specialist
01/11/2022Q: What will display for auto headlamps?
A:
The scan tool displays the status of the auto headlamps. The scan tool displays ACTIVE when the auto headlamps are ON.
By Bob
GM Specialist
01/11/2022Q: What will display for the dimming?
A:
The scan tool displays the state of the panel dimmer switch. The scan tool displays ACTIVE when the park lamps are ON.
By Bob
GM Specialist
01/11/2022See more FAQs (14)