< Back ×
My Vehicle Change Vehicle
2001 GMC Savana 1500
< Back to View All
Fuel Systems
- Department
- Brands
- Prices
OEM (Genuine) 2001 GMC Savana 1500 Fuel Pump
PartNumber: 19332103
Product Specifications- Other Names: Fuel Pump, Sending Unit
- Item Dimensions: 21.1 x 8.1 x 5.9 inches
- Item Weight: 3.20 Pounds
- Fitment Type: Direct Replacement
- Replaced by: 19369946
- Part Description: 2001 GMC Savana 1500 Fuel Pump
Vehicle Fitment- 2001 GMC Savana 1500 | Base, SLE, SLT | 6 Cyl 4.3 L GAS, 8 Cyl 5.0 L GAS, 8 Cyl 5.7 L GAS
$244.83 MSRP:$461.96You Save: $217.13 (48%)
Dorman® Fuel Tank Sending Unit Lock Ring for 2001 GMC Savana 1500
PartNumber: 579-091Product Specifications- Notes: Incls Lock Ring & Gasket; 123 mm OD
- Gasket or Seal Included: Yes
- Inside Diameter: 4''
- Installation Hardware Included: No
- Lock Ring Diameter: 4.125''
- Material: Metal
- OE Part Number: 22552577
- Outside Diameter: 4.25''
- Package Quantity: 1
- Packaging Type: Bag
- UPC: 019495099789
- Part Description: 2001 GMC Savana 1500 Fuel Tank Sending Unit Lock Ring
Vehicle Fitment- 2001 GMC Savana 1500 | All Trims | All Engines
$10.88
OEM (Genuine) 2001 GMC Savana 1500 Fuel Tank Meter/Pump SENSOR KIT
PartNumber: 19121308
Product Specifications- Notes: Gas
- Other Names: Fuel Gauge Sending Unit, Level Sensor
- Item Dimensions: 7.7 x 5.8 x 5.7 inches
- Item Weight: 0.60 Pounds
- Fitment Type: Direct Replacement
- Replaces: 25314262
- Part Description: 2001 GMC Savana 1500 Fuel Tank Meter/Pump SENSOR KIT
Vehicle Fitment- 2001 GMC Savana 1500 | Base, SLE, SLT | 6 Cyl 4.3 L GAS, 8 Cyl 5.0 L GAS, 8 Cyl 5.7 L GAS
OEM (Genuine) 2001 GMC Savana 1500 Fuel Tank Fuel Pump Module Kit
PartNumber: 19177229
Product Specifications- Notes: Diesel Engine; Express, Savana
- Other Names: Fuel Gauge Sending Unit, Sending Unit
- Item Dimensions: 8.4 x 5.2 x 16.8 inches
- Item Weight: 2.20 Pounds
- Fitment Type: Direct Replacement
- Replaces: 25180734
- Part Description: 2001 GMC Savana 1500 Fuel Tank Fuel Pump Module Kit
Vehicle Fitment- 2001 GMC Savana 1500 | Base, SLE, SLT | 6 Cyl 4.3 L GAS, 8 Cyl 5.0 L GAS, 8 Cyl 5.7 L GAS
FAQ for Fuel Sending Unit Repair
Q: What is the removal procedure for the fill valve filter?
A:
You need to remove the O-ring, the circlip, and the fill valve filter, clean the filter in the solvent, blow dry the filter using compressed air, and be sure that the filter passages are clear.
By Bob
GM Specialist
01/11/2022Q: What is the removal procedure for the fuel sender buffer module?
A:
You need to remove the instrument panel passenger knee bolster, and the fuel sender buffer module from the instrument panel passenger knee bolster inner bracket, disconnect the electrical connector from the fuel sender buffer module, and remove the fuel sender buffer module.
By Bob
GM Specialist
01/11/2022Q: What is the recommended torque for the lower cup mounting bolt?
A:
The recommended torque is 12 Nm (106 lb in).
By Bob
GM Specialist
01/11/2022Q: What is the removal procedure for the fuel sender assembly?
A:
You need to disconnect the negative battery cable, relieve the fuel system pressure, drain the fuel tank, and remove the fuel tank and sender assembly.
By Bob
GM Specialist
01/11/2022Q: What is the removal procedure for the fill valve?
A:
You need to relieve the CNG fuel system pressure, disconnect the negative battery cable, and remove the fill line fitting, the fill valve cover, the fill valve jam nut, and the fill valve from the mounting cup.
By Bob
GM Specialist
01/11/2022Q: How to install the fill valve filter?
A:
You need to install the till valve filter, the circlip, and the O-ring.
By Bob
GM Specialist
01/11/2022Q: What is the recommended torque for the fill line fining?
A:
The recommended torque is 37 Nm (27 lb-ft).
By Bob
GM Specialist
01/11/2022Q: How to install the fuel sender buffer module?
A:
You need to position the fuel sender buffer module, connect the electrical connector to the fuel sender buffer module, install the fuel sender buffer module to the instrument panel passenger knee bolster inner bracket, and install the instrument panel passenger knee bolster.
By Bob
GM Specialist
01/11/2022Q: What is the removal procedure for the fill line union (Check valve)?
A:
You need to remove the Fill Line assembly, mark the orientation of the inlet and outlet lines on the check valve, and remove the inlet line and the outlet from the check valve.
By Bob
GM Specialist
01/11/2022Q: What is the removal procedure for the fill valve access cover?
A:
You need to remove the fill valve cover from the mounting cup and remove the fill valve cover tether hold-down pin from the mounting cup.
By Bob
GM Specialist
01/11/2022See more FAQs (11)