2001 GMC Savana 1500 | Base, LS, LT, SLE, SLT | 6 Cyl 4.3 L GAS, 8 Cyl 5.0 L GAS, 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 5.7 L GAS
$32.25MSRP: $50.73
You Save: $18.48 (37%)
FAQ for Door Check Repair
Q: How to install the front side door check strap seal?
A:
You need to apply weatherstrip adhesive to the check strap seal and install the side front door check strap seal to the door.
By Bob
GM Specialist
01/11/2022
Q: What is the removal procedure for the front side door bumper?
A:
You need to open the door, gently pull the top front door bumper from the hole in the door, and pull the bottom front door bumper from the hole in the door.
By Bob
GM Specialist
01/11/2022
Q: What is the recommended torque for the nuts and the washers that retain the sliding side door center track to the body?
A:
The recommended torque is 11 Nm (97 lb in).
By Bob
GM Specialist
01/11/2022
Q: What is the removal procedure for the front door check link?
A:
You need to remove the front door trim panel, the front door water deflector, the bolts that retain the door link to the door jamb, the nuts that retain the door link to the door, and the door link from the door.
By Bob
GM Specialist
01/11/2022
Q: What is the removal procedure for the roller track in the sliding door center (Center)?
A:
You need to remove the passenger side body side trim panel, the sliding side door lower trim panel, the sliding side door center track stop nuts and washers, the sliding side door center track stop, the sliding side door center track cap nut, and plate, the sliding side door center track cap, the sliding side door center roller bracket, the nuts, and the washers and the sliding side door center track from the vehicle.
By Bob
GM Specialist
01/11/2022
Q: What is the removal procedure for the front side door check strap seal?
A:
You need to remove the side front door check the strap seal from the door, and clean the side front door of all of the old adhesive.
By Bob
GM Specialist
01/11/2022
Q: What is the removal procedure for the front side door check strap?
A:
You need to open the door approximately halfway, pull the side door check strap toward the inside of the door, swing the door open, remove the bolts and the nuts that retain the side door check strap to the door pillar, and remove the side door check strap.
By Bob
GM Specialist
01/11/2022
Q: How to install the front side door bumper?
A:
You need to apply mild soap to both the top and bottom bumpers, press the bottom front door bumper into the hole in the door, press the top front door bumper into the hole in the door, and close the door.
By Bob
GM Specialist
01/11/2022
Q: What is the recommended torque for the retaining nuts?
A:
The recommended torque is 11 Nm (97 lb in).
By Bob
GM Specialist
01/11/2022
Q: How to install the front side door check strap?
A:
You need to install the side door check strap into the door, hook the strap to the pin inside of the door, pull the strap to engage the pin, and install the bolts or the nuts to retain the side door check strap.
By Bob
GM Specialist
01/11/2022
See more FAQs (5)
FAQ for Other Repair Info
Q: How to install the power door lock?
A:
You need to install the power Door Lock Actuator, the power door lock actuator retainers to the door lock assembly, and the door lock assembly.
Q: What is the adjustment procedure for the rear side door latch striker in the front?
A:
You need to loosen the sliding side door front striker bolts, slide the door towards the striker, ensure that the lock fully engages the striker, add or delete spacers behind the striker to accomplish this adjustment, and adjust the sliding side door front striker bolts.
Q: How to install the contact plate in the sliding door jamb?
A:
You need to install the electrical connector to the contact plate, the contact plate to the door jamb, and the rivets retaining the contact plate to the door jamb.