< Back ×
My Vehicle Change Vehicle
2001 Chevrolet Venture
< Back to View All
Door Handles, Locks & Related Parts
- Department
- Prices
OEM (Genuine) 2001 Chevrolet Venture Handle, Inside
PartNumber: 16630673
Product Specifications- Location: Driver Side
- Other Names: Handle, Inside
- Item Dimensions: 6.3 x 4.2 x 4.2 inches
- Item Weight: 0.70 Pounds
- Fitment Type: Direct Replacement
- Part Description: 2001 Chevrolet Venture Handle, Inside
Vehicle Fitment- 2001 Chevrolet Venture | Base, LS, LT, Plus, Value, Warner Bros. | 6 Cyl 3.4 L GAS
OEM (Genuine) 2001 Chevrolet Venture Hdl Asm-Inside Remote Control
PartNumber: 16630672Product Specifications- Location: Passenger Side
- Other Names: Handle, Inside
- Item Dimensions: 6.2 x 3.1 x 3.1 inches
- Item Weight: 0.70 Pounds
- Fitment Type: Direct Replacement
- Part Description: 2001 Chevrolet Venture Hdl Asm-Inside Remote Control
Vehicle Fitment- 2001 Chevrolet Venture | Base, LS, LT, Plus, Value, Warner Bros. | 6 Cyl 3.4 L GAS
OEM (Genuine) 2001 Chevrolet Venture Handle Asm-Rear Side Door Inside <Use 1C5L*Black
PartNumber: 10404436
Product Specifications- Location: Driver Side; Passenger Side
- Other Names: Handle, Inside
- Item Dimensions: 6.5 x 2.8 x 1.8 inches
- Item Weight: 0.50 Pounds
- Fitment Type: Direct Replacement
- Replaces: 10270448
- Part Description: 2001 Chevrolet Venture Handle Asm-Rear Side Door Inside <Use 1C5L*Black
Vehicle Fitment- 2001 Chevrolet Venture | Base, LS, LT, Plus, Value, Warner Bros. | 6 Cyl 3.4 L GAS
FAQ for Interior Door Handle Repair
Q: How to remove the front side door inside handle?
A:
You need to remove the front door trim panel, the front door water deflector, and the front door inside handle spring from its retainer clip and remove the front door inside handle from the lock module, pull back on the door inside handle assembly, then separate the upper and lower portions from each other. Slide the upper and lower portions of the lock rods.
By Bob
GM Specialist
01/11/2022Q: What is the proper way to install the front side door inside handle?
A:
You should replace the upper and lower portions on the lock rods, reattach the door inside handle assembly to the lock module, and reattach the front door inside handle spring to its retainer clip, then install the front door water deflector, and the front door trim panel.
By Bob
GM Specialist
01/11/2022Q: What is the proper way to install the assist handle?
A:
You should install the assist handle, the assist handle retaining bolts and the body pillar upper trim panel.
By Bob
GM Specialist
01/11/2022Q: What is the proper way to install the inside handle-sliding door?
A:
You should load the clip into the inside door handle with the open end facing up, align the handle with the shaft on the sliding door, and seat the inside handle to the sliding door. Then if equipped with a power sliding door, enable the PSD system by installing the PSD 15A fuse into the I/P fuse block.
By Bob
GM Specialist
01/11/2022Q: What is the recommended torque for the assist handle retaining bolts?
A:
The recommended torque is 10 N.m (89 lb in).
By Bob
GM Specialist
01/11/2022Q: What kind of special tools will be required in the replacement of the inside handle-sliding door?
A:
The tools required include the Door Handle tool Sliding Door Handle Clip Remover.
By Bob
GM Specialist
01/11/2022Q: How to remove the assist handle?
A:
You need to remove the body pillar upper trim panel, the assist handle retaining bolts, and the assist handles from the vehicle.
By Bob
GM Specialist
01/11/2022Q: How to remove the inside handle-sliding door?
A:
You need to disable the PSD system by removing the PSD 15A fuse if equipped with a power sliding door, then remove the inside door handle clip, and remove the inside handle from the sliding door.
By Bob
GM Specialist
01/11/2022See more FAQs (3)