< Back ×
My Vehicle Change Vehicle
2001 Chevrolet Metro
< Back to View All
Air Filters & Intake Systems
- Department
- Prices
OEM (Genuine) 2001 Chevrolet Metro Body Asm, Throttle (On Esn)
PartNumber: 91173883
Product Specifications- Notes: Metro; All; 1.3l; Auto Trans
- Other Names: Throttle Body
- Item Dimensions: 7.3 x 6.2 x 4.2 inches
- Item Weight: 2.40 Pounds
- Part Description: Body Asm, Throttle (On Esn)
$1405.60 MSRP:$2463.87You Save: $1058.27 (43%)
FAQ for Throttle Body Repair
Q: What is the recommended torque for the bolts and the nuts?
A:
The recommended torque is 18-23 Nm (13.5-17 lb-ft).
By Bob
GM Specialist
02/11/2022Q: What is the removal procedure for the throttle body assembly (SFI)?
A:
You need to drain the engine coolant, remove the bolt and the air inlet duct resonator from the intake plenum, disconnect the breather hose from the valve cover and the air inlet duct from the throttle body, rotate the throttle lever to the wide open throttle position, remove the accelerator cable end from the slot, disconnect the IAC valve electrical connector and the TP sensor electrical connector, disconnect the 2 coolant hoses from the IAC valve coolant fittings, remove the 2 nuts and the 2 bolts that attach the throttle body to the intake plenum, and the throttle body and the gasket.
By Bob
GM Specialist
02/11/2022Q: What is the removal procedure for the manual transmission?
A:
You need to rotate the throttle lever to the wide open throttle position, remove the accelerator cable end from the slot in the throttle lever, loosen the accelerator cable lock-nut, slide the accelerator cable out of the accelerator cable bracket, disconnect the accelerator cable, release the accelerator cable, push the cable through the bulkhead opening, and remove the accelerator cable.
By Bob
GM Specialist
02/11/2022Q: What is the removal procedure for the throttle valve cable/linkage?
A:
You need to remove the adjustment cover of the Throttle Valve (TV) cable, remove the TV cable, raise and suitably support the vehicle, place a drain pan or a suitable container under the transaxle fluid pan, and remove the transaxle drain plug, drain the transaxle fluid, remove the 15 fluid pan bolts, the transaxle fluid pan guard, the fluid pan, and the fluid pan gasket, the TV cable, and the TV cable, and inspect the TV cable O-ring.
By Bob
GM Specialist
02/11/2022Q: How to install the automatic transmission?
A:
You need to install the throttle valve cable assembly through the bulkhead opening, connect the cable stop to the accelerator pedal assembly and the throttle valve cable to the transmission, insert the accelerator cable into the accelerator cable bracket, secure the accelerator cable to the accelerator cable bracket, rotate the throttle lever to the wide open throttle position, insert the accelerator cable end into the slot, and adjust the accelerator cable free-play.
By Bob
GM Specialist
02/11/2022Q: What is the recommended torque for the 15 transaxle fluid pan bolts?
A:
The recommended torque is 6 Nm (53 inch lbs.).
By Bob
GM Specialist
02/11/2022Q: What is the adjustments procedure for the throttle cable/linkage?
A:
You need to measure the accelerator pedal for 2-7 mm (0.08-0.27 in) of free-play, loosen the accelerator control cable locknut, turn the accelerator control cable adjusting nut, tighten the accelerator control cable locknut, measure the accelerator pedal free-play, repeat previous steps until the accelerator pedal free-play is within the specified value, depress the accelerator pedal to the floor, measure the distance between the throttle lever (1) and the throttle stop, adjust the height of the pedal stopper bolt to obtain the specified clearance at the throttle stop, and operate the accelerator control cable from inside the vehicle with the engine off to verify that the throttle movement is smooth and not binding.
By Bob
GM Specialist
02/11/2022Q: How to install the manual transmission?
A:
You need to install the accelerator cable through the bulkhead opening, connect the accelerator cable to the accelerator pedal assembly, insert the accelerator cable into the accelerator cable bracket, secure the accelerator cable to the accelerator cable bracket, rotate the throttle lever to the wide open throttle position, insert the accelerator cable end into the slot in the throttle lever, and adjust the accelerator cable free-play.
By Bob
GM Specialist
02/11/2022Q: What is the service procedure for the throttle body?
A:
You need to soak the metal parts of the throttle body in a cleaner, remove any dirt or any carbon from the air passages in the throttle body, dry all metal components with compressed air, and clean the passages and the throttle bore with compressed air.
By Bob
GM Specialist
02/11/2022Q: What is the adjustment procedure for the throttle valve cable/linkage?
A:
You need to inspect the accelerator cable for play, and adjust the accelerator cable if necessary, start the engine, and let the engine idle until the normal operating temperature has been reached, remove the adjustment cover of the throttle valve (TV) cable, measure the clearance between the TV cable boot and the inner cable stopper, and adjust the TV cable boot-to-inner cable stopper clearance.
By Bob
GM Specialist
02/11/2022See more FAQs (6)