< Back ×
My Vehicle Change Vehicle
2001 Chevrolet Astro
< Back to View All
A/C & Heating
- Department
- Prices
OEM (Genuine) 2001 Chevrolet Astro Cut-Off Switch
PartNumber: 89019183
Product Specifications- Notes: Astro, Safari
- Item Dimensions: 2.6 x 2.0 x 1.2 inches
- Item Weight: 0.40 Pounds
- Fitment Type: Direct Replacement
- Replaces: 2724727, 2724863, 02724863, 02724727
- Part Description: 2001 Chevrolet Astro Cut-Off Switch
Vehicle Fitment- 2001 Chevrolet Astro | Base, CL, CS, LS, LT | 6 Cyl 4.3 L GAS
$51.01 MSRP:$96.26You Save: $45.25 (48%)
OEM (Genuine) 2001 Chevrolet Astro Pressure Valve
PartNumber: 88972205
Product Specifications- Notes: Astro, Safari; Metric Thread
- Other Names: Pressure Valve, Relief Valve
- Item Dimensions: 6.3 x 3.3 x 3.2 inches
- Item Weight: 0.30 Pounds
- Fitment Type: Direct Replacement
- Replaces: 6560606, 09118283, 9118283, 06560606
- Part Description: 2001 Chevrolet Astro Pressure Valve
Vehicle Fitment- 2001 Chevrolet Astro | Base, LS, LT | 6 Cyl 4.3 L GAS
$9.93 MSRP:$18.71You Save: $8.78 (47%)
FAQ for HVAC Pressure Switches Repair
Q: How to install the high-pressure sensor?
A:
After lubricating the new O-ring, you can install the new O-ring and lubricate the control switch housing. Then you can install the switch and the AC high-pressure switch snap ring. After that, you can evacuate and recharge the system. Then you can leak test the fittings of the repaired and install the engine cover.
By Bob
GM Specialist
01/11/2022Q: How to remove the high-pressure sensor?
A:
You need to remove the engine cover and the refrigerant. Then you can clean the control air conditioning (AC) high-pressure switch area before removing the snap ring. After disconnecting the electrical connector from the AC high-pressure switch, you can remove the AC high-pressure switch snap ring, the AC high-pressure switch, and the old O-ring seal from the AC high-pressure switch cavity. Then you need to inspect the AC high-pressure switch cavity and the O-ring groove.
By Bob
GM Specialist
01/11/2022Q: How to install the low-pressure sensor?
A:
You need to coat the new O-ring seal and install the new O-ring seal on the switch. Then you can install the A/C low-pressure switch to the accumulator. After that, you can connect the electrical connector to the A/C low-pressure switch.
By Bob
GM Specialist
01/11/2022Q: What is the recommended torque for the bolts securing the fuel pipe shield to the manifold?
A:
The recommended torque is 6 Nm (53 lb in).
By Bob
GM Specialist
01/11/2022Q: How to remove the low-pressure sensor?
A:
You need to disconnect the electrical connector from the air conditioning (AC) low-pressure switch. Then you can remove the AC low-pressure switch from the accumulator.
By Bob
GM Specialist
01/11/2022Q: What tools do you need to replace the high-pressure sensor?
A:
You need to prepare the J 5403 snap ring pliers, the J 9553-01 O-ring remover, and the J 39400 halogen leak detector.
By Bob
GM Specialist
01/11/2022See more FAQs (1)