< Back ×
My Vehicle Change Vehicle
2001 Buick Regal
< Back to View All
Ignition, Distributors & ECM
- Department
- Brands
- Prices
OEM (Genuine) 2001 Buick Regal Coil Module
PartNumber: 19245558
Product Specifications- Notes: W/O Coil
- Other Names: Coil Module, ECM, Ignition Module, Module, PCM
- Item Dimensions: 9.4 x 4.4 x 2.2 inches
- Item Weight: 1.00 Pounds
- Fitment Type: Direct Replacement
- Replaces: 10475225, 10494012, 12617924, 10469470
- Replaced by: 19435469
- Part Description: 2001 Buick Regal Coil Module
Vehicle Fitment- 2001 Buick Regal | 25th Anniversary Edition, Custom, Gran Sport, GS, GSE, Limited, LS, LSE, Olympic Gold Edition | 6 Cyl 3.8 L GAS
$274.33 MSRP:$517.62You Save: $243.29 (48%)
Cardone Reman® Remanufactured Engine Control Computer for 2001 Buick Regal
PartNumber: 77-9624FProduct Specifications- Notes: with OE # 12209624;Vehicle specific Flash programming req'd ON or OFF the vehicle.Accurate VIN & mileage are req'd. Additional vehicle specific on-car programming must be performed AFTER installation to prevent drivability & starting issues.
- Connector/Terminal Configuration: Pin/Male; Pin/Male
- E-Waste: Yes
- Housing Material: Metal
- Product Condition: Remanufactured
- Removable PROM: No
- Terminal Quantity: 80, 80
- Part Description: 2001 Buick Regal Remanufactured Engine Control Computer
Vehicle Fitment- 2001 Buick Regal | All Trims | All Engines
$95.11
OEM (Genuine) 2001 Buick Regal PCM
PartNumber: 12209624
Product Specifications- Notes: All
- Other Names: ECM, PCM
- Item Dimensions: 13.0 x 8.7 x 4.5 inches
- Item Weight: 4.40 Pounds
- Fitment Type: Direct Replacement
- Part Description: 2001 Buick Regal PCM
Vehicle Fitment- 2001 Buick Regal | GS, LS | 6 Cyl 3.8 L GAS
$318.52 MSRP:$597.04You Save: $278.52 (47%)
OEM (Genuine) 2001 Buick Regal PCM
PartNumber: 9380717
Product Specifications- Notes: All Models; 3.8l; All
- Other Names: Control Module, ECM, PCM
- Item Dimensions: 10.8 x 8.5 x 4.1 inches
- Item Weight: 4.10 Pounds
- Fitment Type: Direct Replacement
- Part Description: 2001 Buick Regal PCM
Vehicle Fitment- 2001 Buick Regal | GS, GSE, LS, LSE | 6 Cyl 3.8 L GAS
$253.42 MSRP:$509.74You Save: $256.32 (51%)
FAQ for Engine Control Module Repair
Q: What should I pay attention to about the engine control module?
A:
You may not program a control module unless you are directed by a service procedure or you are directed by a General Motors Corporation service bulletin. Programming a control module at any other time will not permanently correct a customer's concern.
By Bob
GM Specialist
01/11/2022Q: How to remove the engine control module?
A:
You can disconnect the negative battery cable, remove the air cleaner housing cover assembly, the PCM and harness from the PCM housing, and disconnect the PCM connectors.
By Bob
GM Specialist
01/11/2022Q: How to install the engine control module?
A:
You can reconnect the PCM connectors, reinstall the PCM and harness into the PCM housing, the air cleaner housing cover assembly, and reconnect the negative battery cable.
By Bob
GM Specialist
01/11/2022Q: What is the recommended torque for the bolts?
A:
The recommended torque is 25 Nm (18 ft. lbs.).
By Bob
GM Specialist
01/11/2022Q: What is the service and repair procedure for the engine control module?
A:
You can use a scan tool to clear the DTCs, attempt to start the engine, repeat the Service Programming procedure if the engine does not start or operates poorly, and attempt to program the control module.
By Bob
GM Specialist
01/11/2022Q: How to remove the transmission position switch/sensor?
A:
You can apply the parking brake, shift the transmission into neutral, disconnect the Park/Neutral Position (PNP) switch electrical connectors, remove the manual shaft lever nut, the transmission control lever from the manual shaft, the transmission control lever from the manual shaft, and the PNP switch from the manual shaft.
By Bob
GM Specialist
01/11/2022Q: How to install the transmission position switch/sensor?
A:
You can install the PNP switch to the transmission manual shaft by aligning the switch hub flats with the manual shaft flats, slide the PNP switch onto the transmission manual shaft, and install the PNP switch bolts finger tight, J41364-A onto the PNP switch and the J 41364-A from the switch.
By Bob
GM Specialist
01/11/2022See more FAQs (2)