< Back ×
My Vehicle Change Vehicle
2001 Buick Regal
< Back to View All
Air Bag
- Department
- Prices
OEM (Genuine) 2001 Buick Regal Sensor Asm, Inflator Restraint Side Imp
PartNumber: 9388490
Product Specifications- Notes: Regal
- Other Names: Air Bag Sensor, Side Impact Sensor, Side Sensor
- Item Dimensions: 3.4 x 3.1 x 3.1 inches
- Item Weight: 0.60 Pounds
- Fitment Type: Direct Replacement
- Part Description: 2001 Buick Regal Sensor Asm, Inflator Restraint Side Imp
Vehicle Fitment- 2001 Buick Regal | GS, GSE, LS, LSE | 6 Cyl 3.8 L GAS
$86.99 MSRP:$166.67You Save: $79.68 (48%)
FAQ for Air Bag Sensor Repair
Q: What is the recommended torque for the fasteners?
A:
The recommended torque is 10 N.m (89 lb in).
By Bob
GM Specialist
01/11/2022Q: How to install the steering wheel module?
A:
You can install the horn contact lead, the inflator module electrical connector, and CPA, align the inflator module fasteners to the steering column fastener holes, push the inflator module firmly into the steering column so that the fasteners engage, and enable the SIR system.
By Bob
GM Specialist
01/11/2022Q: How to remove the airbag?
A:
You can disable the SIR system, remove the seat back cover, the inflator module, and the inflator module wiring harness retaining clips from the driver seat frame, pull the inflator module wiring harness, and remove the inflator module from the driver seat back frame.
By Bob
GM Specialist
01/11/2022Q: How to remove the side airbag?
A:
You can disable the SIR system, remove the seat back cover, the inflator module, and the inflator module wiring harness retaining clips from the driver seat frame, pull the inflator module wiring harness and remove the inflator module.
By Bob
GM Specialist
01/11/2022Q: What is the service and repair procedure for the side airbag?
A:
The procedure is to turn off the ignition, remove the ignition key, and the inflator module, place the inflator module on a workbench with the vinyl trim cover facing up and away from the work surface, inspect the J 38826 SIR deployment harness and the appropriate pigtail adapter for damage, connect the appropriate pigtail adapter, extend the SIR deployment harness and adapter to full length from the deployment fixture, connect the inflator module, disconnect the pigtail adapter from the inflator module as soon as possible, and wash hands with a mild soap.
By Bob
GM Specialist
01/11/2022Q: How to remove the steering wheel module?
A:
You can disable the SIR system, turn the steering wheel until two of the opening/holes are on top, install the J 44298 into two of the holes, push the handle back towards the IP, release the two spring-loaded fasteners, turn the steering wheel and repeat the same steps for the other two opening/holes, pull the inflator module gently away from the steering wheel, remove the Connector Position Assurance (CPA), the horn contact lead, and the inflator module.
By Bob
GM Specialist
01/11/2022Q: How to install the side airbag?
A:
You can install the inflator module to the driver seat back frame, and the inflator module, pull the inflator module wiring harness, install the wiring harness retaining clips to the seat frame, and the seat back cover, and enable the SIR system.
By Bob
GM Specialist
01/11/2022Q: How to install the airbag?
A:
You can install the inflator module to the driver seat back frame, and the inflator module, pull the inflator module wiring harness, install the wiring harness retaining clips to the seat frame, and the seat back cover, and enable the SIR system.
By Bob
GM Specialist
01/11/2022Q: What is the scrapping procedure for the air nag?
A:
The procedure is to remove the ignition key, put on safety glasses, remove all loose objects from the front seats, disconnect the inflatable restraint steering wheel module coil connector, cut two 4.6 M (15 ft) deployment wires from a 0.8 mm (18 gauge) or thicker multi-strand wire, connect the deployment harness to the steering wheel module coil connector, disconnect the inflatable restraint side impact module-LF connector, twist together one connector wire lead to one deployment wire, disconnect the inflatable restraint IP module connector, route the deployment harness out of the passenger side of the vehicle, and disconnect all harnesses from the vehicle.
By Bob
GM Specialist
01/11/2022Q: What is the service and repair procedure for the airbag?
A:
The procedure is to remove the ignition key, put on safety glasses, remove the inflator module, place the inflator module on a workbench with the vinyl trim cover facing up and away from the work surface, clear a space on the ground about 1.85 m (6 ft) in diameter, connect the appropriate pigtail adapter, extend the SIR deployment harness and adapter to full length from the deployment fixture, the SIR deployment harness wires to the power source, seat one banana plug into the other, disconnect the pigtail adapter from the inflator module as soon as possible, and wash hands with a mild soap.
By Bob
GM Specialist
01/11/2022See more FAQs (13)