Part Description: 2000 GMC Safari Arm, Windshield Wiper
More Info
Vehicle Fitment
2000 GMC Safari | Base, GT, SL, SLE, SLT, SLX | 4 Cyl 2.5 L GAS, 6 Cyl 4.3 L GAS
FAQ for Windshield Wiper Arms Repair
Q: What's the removal procedure for the wiper arm blade?
A:
The removal procedure is to insert a narrow-bladed screwdriver into the slot over the wiper blade retainer spring, then insert a narrow-bladed screwdriver into the slot over the wiper blade retainer spring, and next remove the wiper blade from the wiper arm.
By Bob
GM Specialist
01/11/2022
Q: What's the installation procedure for the wiper arm blade?
A:
The installation procedure is to install the wiper blade on the wiper arm pin, then snap the wiper blade into place.
By Bob
GM Specialist
01/11/2022
Q: What's the installation procedure for the wiper arm?
A:
The installation procedure is to position the wiper arm assembly on the drive shaft and press in the retaining latch so that the wiper blade aligns with the mark made before the removal, then install the washer hose.
By Bob
GM Specialist
01/11/2022
Q: What's the installation procedure for the rear wiper arm blade?
A:
The installation procedure is to install the wiper blade on the wiper arm pin, then snap the wiper blade into place.
By Bob
GM Specialist
01/11/2022
Q: What's the removal procedure for the wiper arm?
A:
The removal procedure is to remove the washer hose from the wiper arm, lift the wiper arm assembly from the windshield, then pull the retaining latch, and finally remove the arm assembly from the transmission drive shaft.
By Bob
GM Specialist
01/11/2022
Q: What's the installation procedure for the rear wiper arm?
A:
The installation procedure is to position the wiper arm onto the wiper motor drive shaft so that the tip of the blade aligns with the mark made at removal, install the wiper arm onto the drive shaft, press in the retaining clip, then connect the washer hose onto the washer harness connector, insert the hose into the liftgate grommet, lastly operate the rear wiper and inspect for proper operation.
By Bob
GM Specialist
01/11/2022
Q: What's the removal procedure for the rear wiper arm blade?
A:
The removal procedure is to insert a narrow-bladed screwdriver into the slot over the wiper blade retainer spring, then pivot the screwdriver so that the blade tip presses downward on the retainer spring and releases the wiper blade from the pin of the wiper arm, and remove the wiper blade from the wiper arm.
By Bob
GM Specialist
01/11/2022
Q: What's the removal procedure for the rear wiper arm?
A:
The removal procedure is to pull the washer hose through the liftgate grommet, disconnect the washer hose from the washer harness connector, then lift the wiper arm off the liftgate, push out the wiper arm retaining clip with a small screwdriver, and remove the wiper arm from the wiper motor drive shaft.
By Bob
GM Specialist
01/11/2022
See more FAQs (3)
FAQ for Other Repair Info
Q: What's the installation procedure for the windshield washer pump(s)?
A:
The installation procedure is to install the Washer Pump(s) in the washer solvent container, connect the washer hose(s), then install the washer solvent container.
Q: What's the removal procedure for the rear wiper blade element?
A:
The removal procedure is to remove the Wiper Blade from the wiper arm, squeeze the wiper blade element tabs together, then pull the wiper blade element out through the wiper blade claws.
Q: What's the installation procedure for the wiper motor linkage?
A:
The installation procedure is to install the wiper transmission on the vehicle, install the transmission to cowl nuts, then tighten the transmission nuts to 14 N.m (10 lb-ft), next connect the transmission drive link to the wiper motor crank arm using the J 39529, and install the air inlet grille panel, finally install the wiper arms.