< Back ×
My Vehicle Change Vehicle
2000 GMC C3500
< Back to View All
Ignition, Distributors & ECM
- Department
- Brands
- Prices
OEM (Genuine) 2000 GMC C3500 ECM
PartNumber: 16216588
Product Specifications- Notes: 1996-00, W/Diesel; All Models; 6.5l
- Other Names: ECM
- Item Dimensions: 10.5 x 7.2 x 2.4 inches
- Item Weight: 2.10 Pounds
- Fitment Type: Direct Replacement
- Part Description: 2000 GMC C3500 ECM
Vehicle Fitment- 2000 GMC C3500 | Sierra SL, Sierra SLE, Sierra SLT | 8 Cyl 5.7 L GAS, 8 Cyl 6.5 L DIESEL
$294.19 MSRP:$548.16You Save: $253.97 (47%)
Cardone Reman® Remanufactured Vehicle Control Module for 2000 GMC C3500
PartNumber: 77-3494FProduct Specifications- Notes: Knock Module must be removed from original PCM and installed in replacement PCM;Vehicle specific Flash programming req'd ON or OFF the vehicle.Accurate VIN & mileage are req'd. Additional vehicle specific on-car programming must be performed AFTER installation to prevent drivability & starting issues.
- Connector/Terminal Configuration: Pin/Male, Pin/Male, Pin/Male, Pin/Male
- E-Waste: Yes
- Module Housing Material: Metal
- Product Condition: Remanufactured
- Part Description: 2000 GMC C3500 Remanufactured Vehicle Control Module
Vehicle Fitment- 2000 GMC C3500 | All Trims | 8 Cyl 5.7L
- 2000 GMC C3500 | All Trims | 8 Cyl 7.4L
$99.25
OEM (Genuine) 2000 GMC C3500 PCM
PartNumber: 16263494
Product Specifications- Notes: 1996-00, W/O Diesel; All Models; 5.7l, 7.4l
- Other Names: ECM, PCM
- Item Dimensions: 10.8 x 8.2 x 4.1 inches
- Item Weight: 5.60 Pounds
- Fitment Type: Direct Replacement
- Part Description: 2000 GMC C3500 PCM
Vehicle Fitment- 2000 GMC C3500 | Sierra SL, Sierra SLE, Sierra SLT | 8 Cyl 5.7 L CNG, 8 Cyl 5.7 L GAS, 8 Cyl 7.4 L GAS
Cardone Reman® Remanufactured Engine Control Computer for 2000 GMC C3500
PartNumber: 77-6588FProduct Specifications- Notes: with OE # 16216588;Vehicle specific Flash programming req'd ON or OFF the vehicle.Accurate VIN & mileage are req'd. Additional vehicle specific on-car programming must be performed AFTER installation to prevent drivability & starting issues.
- Connector/Terminal Configuration: Pin/Male; Pin/Male; Pin/Male
- E-Waste: Yes
- Housing Material: Metal
- Product Condition: Remanufactured
- Removable PROM: No
- Terminal Quantity: 32, 24, 32
- Part Description: 2000 GMC C3500 Remanufactured Engine Control Computer
Vehicle Fitment- 2000 GMC C3500 | All Trims | 8 Cyl 6.5L
FAQ for Engine Control Module Repair
Q: What should be cautioned about the diode?
A:
If the diode is located next to a connector terminal remove the terminal(s) from the connector to prevent damage from the soldering tool, you can remove the inoperative diode from the harness with a suitable soldering tool.
By Bob
GM Specialist
01/11/2022Q: What should be cautioned in taping the diode to the harness or connector using electrical tape?
A:
To prevent shorts to ground and water intrusion, you should completely cover all exposed wire and diode attachment points with tape.
By Bob
GM Specialist
01/11/2022Q: If the VCM fails to program, what should we do?
A:
We should check all the VCM connections, check the ITCS terminal and equipment for the latest software version, and try again to program the VCM. If the programming fails again, we should replace the VCM.
By Bob
GM Specialist
01/11/2022Q: How do I install the VCM?
A:
You should align the notches of the knock sensor module with the notches in the socket, install the knock sensor module in the socket, install the knock sensor module access cover on the VCM, install the knock Sensor module access cover screws, connect the VCM harness connectors, install the VCM into the VCM bracket, fasten the VCM retainer clip and connect the negative battery cable.
By Bob
GM Specialist
01/11/2022Q: What is the recommended torque for tightening the retaining nut or bolt when installing Engine Controls-MIL ON/Misfire/Misfire DTC's Set?
A:
The recommended torque is 6 N.m (12 lb-ft).
By Bob
GM Specialist
01/11/2022Q: How do I remove the VCM?
A:
You should disconnect the negative battery cable, remove the VCM retainer clip, the VCM, the VCM harness connectors, the knock sensor module access cover screws, and the knock sensor module access cover, gently pinch the retaining clip and pull upward to remove the knock sensor module.
By Bob
GM Specialist
01/11/2022See more FAQs (1)