< Back ×
My Vehicle Change Vehicle
2000 Chevrolet Venture
< Back to View All
Steering Racks & Gearboxes
- Department
- Prices
OEM (Genuine) 2000 Chevrolet Venture Gear Kit, Steering (Remanufacture)
PartNumber: 19330434
Product Specifications- Notes: Remanufactured, W/O AWD; All Models; W/O AWD
- Item Dimensions: 51.3 x 11.1 x 6.2 inches
- Item Weight: 19.00 Pounds
- Fitment Type: Direct Replacement
- Replaces: 26053458
- Part Description: 2000 Chevrolet Venture Gear Kit, Steering (Remanufacture)
Vehicle Fitment- 2000 Chevrolet Venture | Base, LS, LT, Plus, Value, Warner Bros. | 6 Cyl 3.4 L GAS
FAQ for Steering Gearbox Repair
Q: How to remove the power steering gear heat shield?
A:
You should remove the steering gear heat shield bolts/screws as well as the steering gear heat shield.
By Bob
GM Specialist
01/11/2022Q: How to disassemble the rack and pinion boot and breather tube (off vehicle)?
A:
First, you should remove the outer tie rod, the hex jam nut, the tie rod clamp, and the boot clamp. In addition, the rack and pinion boot should also be removed. Next, you should inspect the rack and pinion boot for damage, drain the oil, and then clean the rack and pinion boot.
By Bob
GM Specialist
01/11/2022Q: How to disassemble the Steering Gear Hub Shaft and Bearing - Off Veh?
A:
You should remove the adjuster plug lock nut, the adjuster plug, the adjuster spring, the rack bearing, the retaining ring, the dust cover, the hex lock nut, the stub shaft, the stub shaft seal, and the stub shaft bearing annulus assembly.
By Bob
GM Specialist
01/11/2022Q: How to disassemble the Steering Gear Cyl Pipe and remove the O-ring Seals (Off Veh)?
A:
First, you should loosen both cylinder line fittings. Next, you should remove both cylinder line assemblies and the O-ring seals. Finally, the O-ring seals should be discarded.
By Bob
GM Specialist
01/11/2022Q: How to disassemble the tie rod - inner?
A:
You should remove the rack and pinion boot, the shock damper, the inner tie rod assembly, and the old Loctite (R).
By Bob
GM Specialist
01/11/2022Q: How to install the power steering gear?
A:
You should install the power steering gear, the power steering gear pressure hose, the power steering cooler pipe, the power steering gear heat shield, the frame rear bolts, the steering intermediate shaft, the tie rod ends, and the stabilizer shaft. In addition, you should fill the power steering system and inspect it for leaks.
By Bob
GM Specialist
01/11/2022Q: How to assemble the outer tie rod end?
A:
You should connect the outer tie rod assembly and the prevailing torque nut.
By Bob
GM Specialist
01/11/2022Q: How to assemble the Steering Gear Cyl Pipe and remove the O-ring Seals (Off Veh)?
A:
First, you should inspect the cylinder lines for cracks, dents, and damage. In addition, you should replace the parts as needed. Next, you should install the new O-ring seals and the cylinder line assemblies. Finally, you should flush and bleed the power steering system.
By Bob
GM Specialist
01/11/2022Q: What is the recommended torque for the jam nut?
A:
The recommended torque is 68 N.m (50 ft-lbs.).
By Bob
GM Specialist
01/11/2022Q: How to install the power steering gear heat shield?
A:
You should install the steering gear heat shield as well as the steering gear heat shield bolts/screws.
By Bob
GM Specialist
01/11/2022See more FAQs (16)