< Back ×
My Vehicle Change Vehicle
2000 Chevrolet Blazer
< Back to View All
Air Bag
- Department
- Prices
OEM (Genuine) 2000 Chevrolet Blazer Sensor, Pass Compartment Inflator Restraint Discriminating
PartNumber: 16240665
Product Specifications- Notes: 1998-05, Front
- Location: Driver Side
- Other Names: Front Sensor, Impact Sensor, Sensor
- Item Dimensions: 5.8 x 5.5 x 5.5 inches
- Item Weight: 1.00 Pounds
- Fitment Type: Direct Replacement
- Part Description: 2000 Chevrolet Blazer Sensor, Pass Compartment Inflator Restraint Discriminating
Vehicle Fitment- 2000 Chevrolet Blazer | Base, LS, LT, Trailblazer, Xtreme, ZR2 | 6 Cyl 4.3 L GAS
OEM (Genuine) 2000 Chevrolet Blazer Sensor, Pass Compartment Inflator Restraint Discriminating
PartNumber: 16240655
Product Specifications- Notes: 1998-05, Front
- Location: Passenger Side
- Other Names: Front Sensor, Impact Sensor, Sensor
- Item Dimensions: 7.0 x 6.4 x 4.5 inches
- Item Weight: 0.70 Pounds
- Fitment Type: Direct Replacement
- Part Description: 2000 Chevrolet Blazer Sensor, Pass Compartment Inflator Restraint Discriminating
Vehicle Fitment- 2000 Chevrolet Blazer | Base, LS, LT, Trailblazer, Xtreme, ZR2 | 6 Cyl 4.3 L GAS
FAQ for Air Bag Sensor Repair
Q: What should I ensure before applying power to the front-end sensor?
A:
You need to make sure that the sensor is securely fastened.
By Bob
GM Specialist
01/11/2022Q: What is the recommended size for enlarging the mounting holes?
A:
You are recommended to enlarge the mounting holes in the lower radiator support to 9.0 mm (0.35 in).
By Bob
GM Specialist
01/11/2022Q: What is the recommended torque for the fastener?
A:
The recommended torque for the fastener is 8.0 N.m (71 lb in).
By Bob
GM Specialist
01/11/2022Q: What should we make sure of before applying power to the SDM?
A:
You should make sure that it is securely fastened with the arrow facing toward the front of the vehicle.
By Bob
GM Specialist
28/10/2022Q: How to repair Air Bag Zone 5?
A:
You need to turn the steering wheel until the vehicle's wheels are pointing straight ahead and turn off the ignition. Then you need to remove the key from the ignition and remove the SIR fuse from the I/P fuse block. After that, you can remove the CPA from the I/P module yellow 2-way connector located behind the I/P support. Finally, you need to disconnect the I/P module yellow 2-way connector.
By Bob
GM Specialist
28/10/2022Q: Under what circumstances should we replace the SDM and SDM harness connector?
A:
If the vehicle interior is exposed to moisture and becomes soaked up to the level of the sensing and diagnostic module (SDM).
By Bob
GM Specialist
28/10/2022Q: How to repair Air Bag Zone 3?
A:
You need to turn the steering wheel until the vehicle's wheels are pointing straight ahead and turn off the ignition. Then you need to remove the key from the ignition, remove the knee bolster and you also need to remove the SIR fuse from the I/P fuse block located in the I/P fuse block. After that, you need to remove the connector position assurance (CPA) from the steering wheel module yellow 2-way connector located left of the steering column near the knee bolster. Finally, you have to disconnect the steering wheel module yellow 2-way connector located near the knee bolster.
By Bob
GM Specialist
28/10/2022Q: How to repair zone 1 of the airbags?
A:
You need to turn the steering wheel and turn off the ignition. Then you need to remove the key from the ignition and remove the SIR fuse from the I/P fuse block located in the I/P fuse block. Raising and supporting the vehicle, then you can remove the connector position assurance (CPA) from both inflatable restraints front end discriminating sensor connectors located on the frame crossmember. Finally, you need to disconnect the inflatable restraints front end discriminating sensor connectors.
By Bob
GM Specialist
28/10/2022Q: How many times will the Air Bag indicator flash before turning off?
A:
It will flash 7 times.
By Bob
GM Specialist
28/10/2022Q: How to repair the Air Bag Zone 8?
A:
You need to remove the key from the ignition and connect the I/P module yellow 2-way connector located behind the main I/P support. Then you need to install the CPA to the I/P module yellow 2-way connector located behind the I/P support and connect the steering wheel module yellow 2-way connector located left of the steering column near the knee bolster. After that, you need to install the CPA to the steering wheel module yellow 2-way connector located near the knee bolster and install the SIR fuse to the I/P fuse block located in the I/P fuse block, and you also need to install the knee bolster. Then you need to turn on the ignition with the engine off. Finally, you need to perform the Diagnostic System Check-Restraint Systems if the AIR BAG indicator does not operate as described.
By Bob
GM Specialist
28/10/2022See more FAQs (6)